Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Insert the battery cartridge so that the plus and minus terminals on the bat- Charging light tery cartridge are on the same sides as their respective# markings on the fast charger. Start button tit\ Insert the cartridge fully into the port so that it rests on the charger port floor. Press the start button (red). The charging light will come on and charging will begin. If the charging light does not come on, press the reset button (yellow) first, then the start button (red). If the charging light goes out within 10 seconds even after pressing the reset button and start button a couple of times, the battery cartridge is dead. (CAUTION : Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes oat after about one hour, you may remove the fully charged battery cartridge. After charging, unplug the charger from the power source. CAUTION : Your new battery cartridge is not charged. You will need to charge it before use. Do not keep the button pressed in with tape, etc. or the circuit will not function pro- perly. Also, a malfunction of the charger may result possibly causing overheating, etc. If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try o charge it once more. 1 e When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. e If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Selecting correct socket Use a correct size socket for bolts and nuts. A wrong size socket will result in inaccurate and inconsistent tightening torque. Refer to accessories section for socket size. Fit the socket over the anvil of the tool and push firmly until the spring-loaded de- tent pin on the anvil indexes the hole in the socket. To remove the socket, simply pull it firm- ly. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. I Trigger switch !l CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. .. . . . .. . ...... ... . ... .... . .. . . . ,., . ... . . ..... . . .. .. ;>..: .- .. .. . .... .,.... L . .. . . .,.. . . .... . . .. ... . . . .. . .... . Reversing switch and speed change switch action Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. Slide the speed change switch to the right for high speed (high tightening torque) or to the left for low speed (low tightening torque). Select the speed suitable for your bolt by referring to the figures listed under "Operation". CAUTION : Always check the direction of rotation before operation. .Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. Operation The proper tightening torque may differ depending upon the kind or size of the bolt. The relation between tightening torque and tightening time is shown in the figures below. Standard bo1 t kg cm Iff. Ibrl MI4 l9/16'1 at high rpssd Proper lightening lorqua lor M14 l9/16"1 Proper tightening torquelor M12 1112''I MI0 13/8"l SI low speed Proper ttghtenmg torque lor MI0 1318") Proper tightening torque lor M8 15116'1 I I I 1 0 1 2 3 4 5 seconds Tightening time High tensile bolt kg cm 111 Ibd 800 1581 I MI0 13/8"l ai high speed % 600 6 6 Proper lightening torque lor MI0 l3/8"1 1431- m 2 2 M8 l5/16'1 at high speed 21- Proper lightening torque lor M8 l5/16'l 2w - 1151 I 1 I I I 0 1 2 3 4 5 IeCondl Tighiening time Hold the tool firmly and place the socket over the bolt or nut. Turn the tool on and tighten for the proper tightening time. Speed Type of bolt Tightening time Number of tightenings High High tensile bolt M10 13/8") 3 seconds 90 Low Standard bolt M8 (5/16") 1 second 450 CAUTION : If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. *..:k::. i'i,5i .. .'i'..'.>. , ... .;:;. . :.,"! .. .'.'.j ,,I.::..!_.:. . "... ..::,,:::.y . . _. ... . ;: :?.\:.: . . . . .... .. ..,.. . . . ... .. : ... ,.. .... ..... i:: ... . !,?>. .. ..,. . . .. .. ,. . .. ...... ... .. ... . .. .., .. . . .... . . :. :. +:;.,I. ,.,.. . ii ;;. MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, alwa...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 6900DW (710.09 kb)