Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in. NOTE : 0 Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. *When driving wood screws, predrill pilot holes to make driving easier and to pre- vent splitting of the workpiece. See the chart. 4.5 (1 1/64',) 2.9 -3.2 17/64' -118'7 4.8 13/16") 3.1 -3.4 (1/8" -9/64") 5.1 113164'1 3.3 -3.6 (1/8" -9/64"] 5.5 17/32',) 3.7 -3.9 19/64" -5/32',) 5.8 17/32") I 4.0 -4.2 (5132'' -11/64',) 6.1 (15/64') I 4.2 -4.4 (11/64" -11/64") Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the *\- marking. Then proceed as follows. 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer at the point to be drilled place the point of the bit in the indenta- tion and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. CAUTION : .Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. .There is a tremendous force exerted on the tool/bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece. .A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. .Always secure small workpieces in a vise or similar hold-down device. Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20-30 seconds before resuming operation. CAUTION : Always withdraw the tool from the workpiece before resuming operation. If the tool cannot be withdrawn, hold the tool firmly when turning on the tool, to overcome a strong reaction. Hook A hook is provided as a standard equip- ment. This hook is convenient for tem- porarily hanging the tool. To install the hook, first insert one end of the hook into one slot in the tool body and then insert the other end into the other slot. Secure the hook with the screw. The hook can be installed on either left or right side of the tool. MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits 1 1 I Size I Part NO. Slotted .-784010-0A #ffF L=l-t=j 78401 1 -0A Square drill bit 7 8 4 6 06-0A - Rubber pad assembly Part No. 123001-2 Foam polishing pad Part No. 743023-2 Wool bonnet Part No. 743401-6 Plastic carrying case Fast charger Model DC1201 Part No. 11 31 26-0 Battery cartridge 91 00 Part No. 19201 9-4 High capacity battery 9101 Part No. 192321-5 Power display battery (High cap.] 9101A Part No. 192404-1 Battery cover Part No. 414938-7 Belt clip Part No. 343951-7 Sep.-08-’94 US CORDLESS DRIVER DRILL Model 6202D Note: The switch and other part configurations may differ from country to country. MODEL 62020 Sep.-08-'94 US DESCRIPTION DESCRIPTION :SD MACHINE MACHINE __ 1 1 Housmg Set IWith Item 591 33 ~ 1 Flat Washer 16 2 1 Name Plate 34 1 Spur Gear 15 3 1 Pan Head Screw M4x22 Wth Washer) 35 1 Spur Gear 15 4 7 Tapptng Screw BT4x20 36 1 Spur Gear 15 5 1 Hand Strap 37 1 Internal Gear 48 6 1 Set Plate 38 1 Flat Washer 18 7 1 Switch 39 1 DC Motor 8 1 Lever 40 1 Sponge 14-72 9 1 Switch Lever 41 1 Sponge 14-72 10 1 Pan Head Screw M5x22 42 1 Plane Bearing 4 11 1 Keyless Drill Chuck 10 43 1 Flat Washer 4 12 1 Spindle 44 1 Compression Spring 8 13 1 PI" 4 45 1 Thin Washer 8 14 1 Bearing Retainer 14 46 1 Spur Gear 25 15 1 Ball Bearing 6000LLB 47 1 Ring 12 16 1 Stop Ring E-9 48 1 Spur Gear 40 17 1 Change Ring 49 1 Thin Washer 8 18 2 Cam Plate 50 1 Compression Spring 8 19 2 Pan Head Screw M4x12 lWith Washer) 51 1 Stop Ring E-7 20 1 Slider 52 1 Ball Bearing 608LLB 21 1 Flat Washer 10 53 1 Spur Gear 8 22 1 Thrust Needle Gauge 1023 54 1 Key 3 23 1 Washer 10 55 1 Countersunk Head Screw M4x12 24 1 Wave Washe...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 6202DW (824.62 kb)