Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
User’s Guide # L010167 Step Motor Selection Guide elpmaxrEotoM tnerrurCotoM edorCebmuN ralopinU gnitaR kaesPeireS gnitaR kaelPellaraP gnitaR seireS tnerruC gnitteS lellaraP tnerruC gnitteS 1D32 20S 20 A0.1 A0.1 A0.2 ----%5 3L32 30 8WL-D 30 A5.1 A5.1 A0.3 %0 %02 1N43 40 8WL-S 40 A0.2 A0.2 A0.4 %5 %03 04L32 50 8WL-D 50 A5.2 A5.2 A0.5 %01 %04 1A43 60B 60 A0.3 A0.3 A0.6 %02 %05 2N43 70 8WL-S 70 A5.3 A5.3 A0.7 %52 %06 1K43 80 8WL-S 80 A0.4 A0.4 A0.8 %03 %07 2N24 90 BC-S 90 A5.4 A5.4 A0.9 %53 %58 3L32 01 8WL-S 01 A0.5 A0.5 A0.01 %04 %001 3D43 11D 11 A5.5 A5.5 A0.11 %54 %001 1K24 21 BC-S 21 A0.6 A0.6 A0.21 %05 %001 2D43 31S 31 A5.6 A5.6 A0.31 %55 %001 3N43 41 8WL-S 41 A0.7 A0.7 A0.41 %06 %001 1N24 51 BC-D 51 A5.7 A5.7 A0.51 %56 ---- 4K43 61 8WL-S 61 A0.8 A0.8 A0.61 %07 ---- 1D24 91D 91 A5.9 A5.9 A0.91 %09 ---- 3N24 22 BC-S 22 A0.11 A0.11 A0.22 %001 ---- 2D24 52S 52 A5.21 A5.21 A0.52 %001 ---- TABLE 5 - Table Selection for Anaheim Automation Motor Current Settings. Anaheim Automation offers motor cable, making hook-ups quick and easy! Contact the factory or visit our website for more motor and cable offerings. Reducing Output Current Reducing the output current is accomplished by setting switch 1 of the DIP switch to the ON position and occurs approximately 1 second after the last positive going edge of the step clock input. The amount of current per phase in the reduction mode is approximately 70% of the set current. When the current reduction circuit is activated, the current reduction resistor is paralleled with the current adjustment poten tiometer. This lowers the total resistance value, and thus lowers the per Phase output current. Determining Output Current The output current for the motor used when microstepping is determined differently from that of a full/half step unipolar driver. In the MBC08161, a sine/cosine output function is used in rotating the motor. The output current for a given motor is determined by the motors current rating and the wiring configuration of the motor. There is a current adjustment potentiometer used to set the output current of the MBC10641. This sets the peak output current of the sine/cosine waves. The specified motor current (which is the unipolar value) is multiplied by a factor of 1.0, 1.4, or 2.0 depending on the motor configuration (series, half-coil, or parallel). December 2004 Step Motor Configurations Step motors can be configured as 4, 6, or 8 leads. Each configuration requires different currents. Refer to the lead configurations and the procedures to determine their output current. WARNING! Step motors will run hot even when configured correctly. Damage may occur to the motor if a higher than specified current is used. Most specified motor currents are maximum values. Care should be taken to not exceed these ratings. 6 Lead Motors When configuring a 6 lead motor in a half-coil configuration(connected from one end of the coil to the center tap), multiply the specified per Phase (or unipolar) current rating...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - DPG10003-01 (618.15 kb)
Дрели и шуропопверты - DPG10002-01 (618.15 kb)
Дрели и шуропопверты - DPG10003-01 (618.15 kb)
Дрели и шуропопверты - DPG10002-01 (618.15 kb)