Оценок - 4, средний балл: 3.5
(
)
)
|
Фото и характеристики Makita 6834 |
Фрагмент инструкции
An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating Volts Total length of cord in feet 120 V 25 ft. 50 ft. 100 ft. 150 ft. More Than Not More Than AWG 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended SPECIFIC SAFETY RULES USB004-2 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to screwdriver safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces 3. Hold the tool firmly. when performing an operation where the 4. Keep hands away from rotating parts. cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will 5. Do not touch the bit or the workpiece make exposed metal parts of the tool “live” immediately after operation: they may be and shock the operator. extremely hot and could burn your skin. 2. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. SAVE THESE INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD201-2 The followings show the symbols used for tool. V .......................volts n....................no load speed ° A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current FUNCTIONAL DESCRIPTION 002629 1 2 1. Lock button 2. Switch trigger 002636 1 1. Reversing switch 002648 1 1. Hook CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. Reversing switch action This tool has a reversing switch to change the direction of rotation. Press the upper side (FWD side) of the reversing switch for clockwise rotation or the lower side (REV side) of the reversing switch for counterclockwise rotation. CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. Hook The hook is convenient for hooking the tool to your belt. It can be installed on either side of the tool. To remove it, pull it out in the direction of the arrow while raising. To install the hook, push it down until it “clicks” into place on the tool. ASSEMBLY 1 2 1. Casing 2. Thumb screw 12 3 1. Dust cover 2. Plane bearing 3. Bit 1 2 3 4 1. Lever 2. Stopper base 3. Plate 4. Casing CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit 002656 Loosen the thumb screws which secure the casing. Pull out the casing in the direction of the arrow. 002657 Press the dust cover toward the plain bearing and pull out the bit. If the dust cover cannot be moved as far as the plain bearing, try it again after turning the bit slightly. To install the bit, insert it into the socket while turning it slightly. After installing, always make sure that the bit is securely held in place by trying to pull it out. 002663 Setting for desired screw length There are 3 (for Model 6833) or 5 (for Model 6834) positive- lock screw length settings. To obtain the desired setting, pull out the stopper base while depressing the lever until you see the number of the desired screw length (indicated on the plate) appear to rest on the very top edge of the casing. See the table below for the relation between the number indicated on the plate and the respective screw length ranges. Number indicated on the plate Screw length range 25/28 25 mm (1”) - 28 mm (1 - 1/8") 32 28 mm (1 - 1/8”) - 35 mm (1 - 3/8”) 40 35 mm (1 - 3/8”) - 41 mm (1 - 5/8”) * 51 41 mm (1 - 5/8”) - 51 mm (2”) * 57 51 mm (2”) - 57 mm (2 - 1/4”) (Note) * for Model 6834 only 1. Stopper plate 2. Casing 3. Adjusting knob A B 1 2 3 5mm (3/16") 1 2 3 1 002667 1. Stopper plate 2. Casing 3. Adjusting knob A B 1 2 3 5mm (3/16") 1 2 3 1 002667 1. Driving position 002665 Adjusting the driving depth Depress the stopper base as far as it will go. While keeping it in this position, turn the adjusting knob until the bit tip projects a...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 6833 (134.04 kb)