Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
NOTE : 0 Use the proper bit for the head of the screw that you wish to use. 0 Hold the tool pointed straight at the screw. 0 If you fasten the screw for a time longer than shown in the figures above, the screw or the screw or the point of the driver bit may be overstressed, stripped, damaged, etc. Before starting your job, always perform a test operation to verify the adequate fasten- ing time for your screw. When fastening a machine screw in a steel plate, the proper fastening torque can be obtained in an extremely short time (approx. 0.1 -0.2 seconds). Turn the tool off as soon as the impact sound is heard. .When fastening screw M8 (5/16") or smaller, carefully adjust pressure on the switch trigger so that the screw is not damaged. The fastening torque is affected by a wide variety of factors including the following. After fastening, always check the torque with a torque wrench. 1. When the battery cartridge is discharged almost completely, voltage will drop and the fastening torque will be reduced. 2. Drive bit or socket bit Failure to use the correct size driver bit or socket bit will cause a reduction in the fastening torque. 3. Bolt 0 Even though the torque coefficient and the class of bolt are the same, the proper fastening torque will differ according to the diameter of the bolt. 0 Even though the diameters of bolts are the same, the proper fastening torque will differ according to the torque coefficient, the class of bolt and the bolt length. 4. The type of materials to be fastened and the manner of holding the tool will affect the torque. 5. Operating the tool at low speed will cause a reduction in the fastening torque. CAUTION : If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Size Part No. Model DC1201 Phillips #2 784214-0A #3 784215-0A Battery cartridge 1200 Fast charger Part No. 192271-4 Model DC1290 Part No. 1131 19-7 High capacity battery 1201 Part No. 192296-8 Battery cover Power display battery (High cap.) 1201A Part No. 192407-5 Part No. 414938-7 Plastic carrying case Apr -20-'95 US CORDLESS IMPACT DRIVER Model 6913D Q Note: The switch and other part configurations may differ from country to country. Apr.-20-'95 US MODEL 6913D ITEM NO. 'Fz $2D DESCRIPTION DESCRIPTION NO. USED MACHINE 1 1 Ring Spring 11 19 1 2 1 Flat Washer 12 20 1 3 4 1 1 Compression Spring 13 Sleeve 21 22 1 1 5 6 1 1 Hm"r Case Complete Nylon Washer 14 23 24 1 8 7 2 Steel Ball 3 5 25 1 8 1 Anvil 26 1 9 2 Steel Ball 5 6 21 1 10 1 Hammer 28 1 11 24 Steel Ball 3 5 29 1 12 1 Flat Washer 22 30 1 13 1 Compresslo" Sprtng 24 31 1 15 1 Spindle 32 1 16 17 4 1 Tapping Screw Flange PT 4x20 Rubber Sleeve 8 33 34 1 1 18 1-Plane Beam0 4 -- Note The switch and other part specifications may differ from country to country. Gear Complete 13-47 Plane Bearing 4 Rubber Sleeve 8 DC Motor 12 V Name Plate Tapping Screw 4x18 Housing Set (With Item 331 Battery Holder High Capacity Batlery 1201 Set Plate Hand Strap Switch Lever Swnch Lever Housing Set IWith Item 251 Makita Label Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under "Tools-Electric': Warranty Policy Every Makita tool is thorou& inspected and tested before leaving the factory. It 1s warranted to be free of defects from workmanship and matenals for the period of ONE YEAR from the date of original purchase. Should any trouble develop dunng this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (01at our option. replace) without charge. This Warranty does not apply where: repairs have been made or attempted by others. repurs are required because of normal wear and ...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 6913D (685.87 kb)
Дрели и шуропопверты - 6913DW (685.87 kb)