Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
.To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool. 0 Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the bat- tery cartridge are on the same sides as their respective markings on the fast charger. In- sert the cartridge fully into the port so that it rests on the charger port floor. The charging light will come on and charg- ing will begin. If the charging light does not come on, press the reset button. If the charging light goes out within 10 seconds even after pressing the reset button a couple of times, the battery cartridge is dead. (CAUTION : Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. After charging, unplug the charger from the power source. CAUTION : 0 Your new battery cartridge is not charged. You will need to charge it before use. 0 If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Switch action I 0 Set the reversing switch lever just in front of the trigger switch to Forward (FWD) Reversing switch lever or Reverse (REV). Then pull the trigger I to turn the tool ON and release it to turn it OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the switch lever to the opposite side. The trigger switch does not work if the switch lever is in the neutral position. Trigger switch I CAUTIONS: 0 Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. When not operating the tool, keep the lever switch in the neutral position. 0 Before operation, always check to be sure that the switch lever is set for the desired direction of rotation. 0 Pulling the trigger hard when the lever switch is set to neutral can cause switch breakage. 7 Fastening torque adjustment I 0 The fastening torque may be adjusted by Fastening torque adjustment ring turning the adjustment ring to align the Bit notched line on the ring with a number on the indicator label. However, the clearance between the ring and the cap is 2.5 mm (1/8") maximum after one full turn, and the ring should not be forced beyond this point. 0 Turning the adjustment ring in the arrow direction obtains a higher torque (HI side); turning in the opposite direction gives a lower torque (LOW side). .Aligning the notched line with the number 4 on the indicator label provides the right torque for setting a 4 mm (1/8") screw. Aligning to the 5 and 6 is suitable to drive a 5 mm (3/16") and 6 mm (1/4") screw, respectively. - 0 If the adjust ring will not turn easily, switch the tool on and wait for the clutch to cut in before making the torque adjustment. .To back out (remove) an already driven screw, use a little more torque than you used to drive the screw initially. .Switch off as soon as the clutch cuts in. Continuous unnecessary clutching will loosen the adjust ring and make it impossible to obtain the desired torque. Grip .The grip shown on the right is recom- mended. 8 Hole 0The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. Drill chuck (Accessory) 0 To install a drill chuck, remove the insert bit by a strong jerk, then a drill chuck can be replaced with the insert bit by a sharp push of the hand. .To install the drill bit, place it in the chuck as far as it will go. Tighten the chuck collar by hand. Place the chuck key in each of three holes, and tighten clockwise. 0 To remove the drill bit, place the chuck key into the chuck hole and turn counterclock- wise. CAUTIONS: 0 Be sure that the battery cartridge has been removed from the tool. Always set the Forward-Reverse switch lever to NEUTRAL when installing, removing or adjusting bits or accessories. Screwdriving Item Rominal Diameter (mm) I Match your bit to your screw. Bit No. Wood Screw Phillips bits Select your screws on the nominal dia-2.1 -2.7 13/32''-118") and right...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 6710DW (727.96 kb)