Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
A battery that gets too hot can be permanently damaged. Never over-discharge a battery by using the tool even after tool performance is decreasing. Never attempt to discharge a tool’s battery by continuing to pull the tool trigger. When tool performance begins to diminish, stop the tool, recharge the battery and use the fresh battery for optimal performance. 12. Recharge the battery monthly even if not used. 13. Always remove the battery from the Impact Driver before performing inspection, maintenance, cleaning procedures, or storage. 14. Caution: Never charge Battery for more than 5 hours continuously. Charger Adapter should not be left plugged in or charging for more than 5 hours. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 94371 For technical questions, please call 1-800-444-3353 Page 4 Unpacking When unpacking, check to make sure the following parts are included: Impact Driver, Battery, Charger Base, and Charger Adapter. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Operation CHARGING BATTERY The Battery (30) does not come charged from the factory. Charge before using. Refer to photos on the next page. 1. Push the two side buttons in on the Battery, then slide the Battery off the Impact Driver handle. 2. Slide the Battery into the Charger Base (48). The battery can only insert one way using the guide tabs. 3. Plug the Charger Adapter (49) output cord into the Charger Base connector. 4. Plug the Charger Adapter line cord into an electrical outlet. Verify on the Charger Base that the red charging indicator light come on. If it does not come on, check the power connection or try a different wall outlet. Charge the new Battery for 5 hours. Subsequent charges will take 4 to 5 hours. 5. Unplug the Charger Base from the electrical outlet when the Battery is fully charged.The Charging Indicator will flash red. Note: The operation time of a new battery will ramp up as it is properly used (drained) and recharged. It will take about 5 recharging cycles before the Battery is at maximum efficiency. Caution: If two or more batteries are to be charged, avoid damaging the Charger by allowing it to cool down between charges.Wait for the Battery to cool down before placing in the Impact Driver. SKU 94371 For technical questions, please call 1-800-444-3353 Page 5 Charger Base (48) Battery (30) Charging Indicator Charger Adapter (49) Charger Base (48) Battery (30) Charging Indicator Charger Adapter (49) INSERTING BATTERY Caution: Before inserting the Battery into the tool, be certain that the Trigger Switch (21) is in the Off position. 1. Push the Forward/Reverse Button (31) to the center position to lock the Switch in the Off position. 2. Insert Battery into the receptacle at the handle-bottom of the Impact Driver. 3. Secure the Lock-spring Clasps to each side of the handle. SCREWDRIVER 1. Insert a hex screwdriver bit (not provided) into the Chuck. See photos on the next page. 2. Press the Forward / Reverse Switch (31) to desired position. Forward position: fasten (clockwise rotation). Reverse position: removing fasteners or freeing screws (counterclockwise rotation). Centerposition: locked. 3. Press (and hold) the Variable Speed Switch to turn on. This Switch varies the speed depending on how far in it is pressed. Avoid overloading the Impact Driver. Do not apply excessive pressure or speed while driving screws. If the drill speed drops abnormally, decrease pressure immediately. If the bit stops abruptly, or the bit becomes stuck, release Switch at once. SKU 94371 For technical questions, please call 1-800-444-3353 Page 6 Forward / Reverse Rotation Button Trigger Switch (21) Variable Speed Driver Bit (not supplied) Lock-spring Clasps Forward / Reverse Rotation Button Trigger Switch (21) Variable Speed Driver Bit (not supplied) Lock-spring Clasps Troubleshooting Symptom Possible Cause Remedy Trigger Switch locked in place. Forward / Reverse button in center position. Move button to the left or right for forward or reverse operation. Impact Wrench operates slowly or without force. Battery weak. Recharge Battery completely. Impact Wrench does not turn on. Battery completely discharged. Recharge Battery completely. Battery will not hold charge. Battery dead. Replace with new Battery. Maintenance 1. Keep tools clean by wiping with a damp cloth. 2. Store tools in carrying case when not using; avoid storing in high temperature areas. 3. When the battery becomes weak, and the tool loses power, keep the tool turned On until the battery is completely drained before recharging. This will ensure a full recharge. 4. Recharge battery monthly when not in use to maintain battery life. When the battery i...