Оценок - 0, средний балл: 4
(
)
)
|
Фрагмент инструкции
helping to prevent damage to the screw, bit, or workpiece. The higher the number, the more torque is applied before the clutch slips. Unless you are drilling, always start with a lower number to help prevent damage. This drill also has torque settings between the numbers to allow a greater range of control. Drill Setting (): This setting essentially prevents the clutch from slipping entirely. It is designed for drilling, but is not advised for using the screwdriver because it offers no protection against stripping the head or splitting the wood. Set the drilling torque by turning the Torque Setting Ring (15) to align the torque 4. indicator arrow with the desired setting. (See Figure E., previous page.) When drilling in light gauge metal or wood, use a wooden block to back up the 5. material to prevent damage to the workpiece. Mark the center of the hole to be drilled with a center punch (not included) to give 6. a Drill Bit a start and to prevent it from “walking”. Lubricate the Drill Bit with cutting oil (not included) when drilling iron or steel. Use 7. a coolant (not included) when drilling nonferrous metals such as copper, brass, or aluminum. Attach the Accessory Grip (14) to the drill by sliding the metal loop over the front 8. of the drill and fastening it securely behind the Torque Setting. Turn the handle of Accessory Grip clockwise until it holds firmly. The Accessory Grip allows greater control over the Drill and makes it easier to resist being pulled out of alignment by torque. Insert the fully charged Battery Pack (28) into the Handle of the Cordless Drill.9. The Rotation Button (9) allows you to change the rotational direction of the 10. Cordless Drill. For a clockwise rotation, move the Rotation Button to the right. For a counterclockwise rotation, move the Rotation Button to the left. The center position locks the Trigger (10), helping to prevent the Drill from operating. The Forward/ Reverse Indicator (21) lights up, when the Trigger is depressed, to show which direction the Drill is set. Make sure to hold the Cordless Drill firmly with both hands, as torque from the Motor 11. can cause the tool to twist. Operate the Drill, by squeezing the Trigger (10). The speed of the Drill can be 12. controlled by varying the pressure on the Trigger. If Drilling:13. Use the Drill torque setting, as described above. REV 09h Drill only as deep as necessary. Do not drill deeper than necessary into walls or other areas where you cannot identify any possible hazards behind the drilling surface. To reduce jamming as the Bit breaks through the workpiece, decrease the drilling pressure when the point of the Bit breaks through the workpiece. When you have drilled the hole, remove the Bit from the hole while the Cordless Drill 14. is still running. This prevents the Bit from getting caught in the hole and causing damage. When driving screws, start with a low torque setting.15. If the clutch starts slipping before the screw is in all the way, stop the drill, put the 16. Rotation Button (9) in the center position and change the torque setting. Reset the rotation direction before continuing. Release the Trigger (10) to stop the Drill. Then, remove the Battery Pack, put the 17. Rotation Button in the center position, and remove the bit from the Drill. INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Remove the Battery Pack (28) from the tool and set the Rotation Button (9) to its center, locked position before performing any inspection, maintenance, or cleaning. BEFORE EACH USE,2. inspect the general condition of the Cordless Drill. Check for misalignment or binding of moving parts, cracked or broken parts, leaking Battery Pack, damaged Charger wiring, chipped or broken Drill Bits, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. DAILY:3. With a soft brush or cloth, remove all dirt and debris from the Cordless Drill. Do not immerse the Cordless Drill in any liquids. When the battery needs replacement keep in mind that the Nickel-Cadmium 4. (Ni-Cd) battery in this tool must be recycled or disposed of properly. Parts list Part Description QTY 1 Screw 2 2 Sticker 1 3 2-Head Bit 1 4 Plate 1 5 Battery Indicator Button 1 6 Bit Clamp 1 7 Battery Indicator PCB 1 8 Left Shell 1 9 Rotation Button 1 10 Trigger 1 11 R/R Indicator PCB 1 12 Magnesium Shell 1 13 Screw 1 14 Accessory Grip 1 15 Torque Setting Ring 1 Part Description QTY 16 Chuck (13mm) 1 17 Screw 1 18 Gear Assembly Motor 1 19 Right Shell 1 20 Cover 1 21 Forward/Reverse Indicators 1 22 Level Vial 1 23 Screw 1 24 Insulated Pipe 1 25 Battery Clamp Housing 1 26 Wire 8 27 Battery Clamp 1 28 Battery Pack 1 29 Charger (not shown) 1 30 Adapter (not shown) 1 ASSEMBLY DIAGRAM PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANU...