Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The correct tool will do the job better and safer at the rate for which it is designed. 3. Do not use the power tool if the Throttle lever does not turn it on or off. Any tool that cannot be controlled with the Throttle Lever is dangerous and must be replaced. 4. Disconnect the air hose from the tool before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 5. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 6. Maintain tools with care. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. 7. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 8. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERvICE 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of injury. SPECIFIC SAFETY RUlES 1. Maintain labels and nameplates on the Ratchet Wrench. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. CAUTION! To avoid injury, grip the Ratchet Wrench firmly with both hands. SKU 93821 For technical questions, please call 1-800-444-3353 PAGE 4 3. Use clean, dry, regulated, compressed air at 90 PSI. Do not exceed the recommended 90 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. 4. When connecting to the air supply: Prior to each use, if an automatic oiler is not used, add two drops of air tool oil (not included) into the Air Inlet (10) fitting of the Ratchet Wrench. 5. Always disconnect the Ratchet Wrench from its compressed air supply source, and squeeze the Throttle lever (11) to release all compressed air in the tool before performing any maintenance or services. 6. Industrial applications must follow OSHA requirements. 7. WARNING! chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code 25249.5, et seq.) The brass components of this product contain lead, a 8. WARNING! The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. ASSEMBlY AND OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 9. To Attach A Quick Connector: 1. Prior to use, the Ratchet Wrench requires the attachment of a Quick Connector (not included) into its Air Inlet (10). To do so, wrap approximately 3” of pipe thread sealer tape (not included) around the male threads of a Quick Connector. Then, firmly tighten the Quick Connector into the Air Inlet. (See Figure A.) SKU 93821 For technical questions, please call 1-800-444-3353 PAGE 5 Recommended Compressed Air System Set-Up: 1. For best service, you should incorporate an oiler, regulator, and inline filter when using an air compressor (not included) to operate the Ratchet Wrench. (See Figure B.) RECOMMENDED COMPRESSED AIR SYSTEM SET-UP ATTACH QUICK CONNECTOR TO RATCHET WRENCH FIGURE B To Operate The Ratchet Wrench: 1. The Ratchet Wrench is designed to work with all 1/4” drive sockets (not included). Before installing a socket, make sure your hand is away from the Throttle Lever (11). When installing a socket onto the Drive Head of the Ratchet Wrench, always make sure the socket is firmly secured in the Drive Head. (See Figure C, next page.) 2. After installing a socket onto the Drive Head of the Ratchet Wrench, set the Forward/Reverse Knob (33) to the direction in which you wish the Ratchet to turn (Forward = clockwise rotation / Reverse = counterclockwise rotation). (See Figure C.) 3. Connect the air supply hose to the Ratchet Wrench. Turn on the air compressor, and set its regulator to the recommended 90 PSI for the Ratchet Wrench. 4. Insert the socket onto the bolt or nut that is to be loosened/tightened. 5. Make sure to hold the Ratchet Wrench firmly with both hands, as torque will cause the tool to twist. Then gently squeeze the Throttle Lever (11) to tighten or loosen the bolt/nut. Apply additional pressure on the Throttle Lever (11) as needed. (See F...