Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
minimum recommended Brings air to point of use H Air Hose Connects air to tool I Filter Prevents dirt and condensation from J Regulator Adjusts air pressure to tool K Lubricator (optional) For air tool lubrication L Coupler and Plug Provides quick connection M Leader Hose (optional) Increases coupler life N Air Cleaner / Dryer Prevents water vapor O Air Adjusting Valve (optional) For fine tuning airflow Safety Setup Operation Maintenance Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the trigger before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. Improper adjustment can result in tool failure or other serious hazards. Side Handle Installation 1. Slide the Handle Ring (35) over the front of the housing in the desired position. 2. Install the Handle (34) over the threaded portion of the Handle Ring (35) and tighten securely. Drill Bit Installation CAUTION! Wear heavy-duty work gloves to provide protection when inserting and removing drill bits. Drill bits become very hot during use. Do not remove drill bits until the bit has cooled. 1. Loosen the Chuck with the Chuck Key until the jaws of the drill are opened enough to fit the drill bit. 2. Place the desired drill bit into the drill between the Chuck Jaws. Note: In addition to single or double-ended screwdriver bits, adapters with hexagonal shafts with matching socket heads can also be used. 3. Hand tighten the Chuck until the bit is held securely in place, centered between the Chuck Jaws. 4. Insert the tip of the Chuck Key into a hole on the side of the Chuck so that the teeth on the Key engage the gear on the Chuck. Use the Key to tighten the Chuck securely and remove the Key. NOTICE: Use sharp bits. Dull, bent, or damaged bits will cause stress on the drill and/or break. Safety Setup Operation Maintenance Workpiece and Work Area Set Up 1. Designate a work area that is clean and well.lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the air hose to possible damage. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. 3. Secure loose workpieces using a vise or clamps (not included) to prevent movement while working. 4. There must not be hazardous objects (such as utility lines or foreign objects) nearby that will present a hazard while working. General Operating Instructions 1. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use. 2. Place the bit at the point to be drilled. Note: If drilling metal or another hard, smooth surface, use a punch to mark the drill location. Metal Cutting: Use a cutting oil with some metals to prolong the life of the bit and increase the drilling action. • Steel, tin, or sheet metal: Use a light machine oil. • Aluminum: Use paraffin. • Brass, copper, or cast iron: Do not use a lubricant. 3. Grasp the drill firmly with both hands while slowly squeezing the Trigger (8). Do not force the drill. Only apply light pressure when drilling. 4. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool. CAUTION! TO PREVENT INJURY FROM TOOL OR ACCESSORY FAILURE: Do not exceed the tool's maximum air pressure rating. If the tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger tool may be required. 5. To prevent accidents, turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the trigger after use. Clean external surfaces of the tool with clean, dry cloth, and apply a thin coat of tool oil. Then store the tool indoors out of children's reach. Safety Setup Operation Maintenance User.Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the trigger before performing any inspection, maintenance, or cleaning procedures. T...