Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
maintEnancE OpERatiOnSEtup SaFEty Item 93100 For technical questions, please call 1-800-444-3353. Page 7 Page 8 For technical questions, please call 1-800-444-3353. Item 93100 Safety Operation Maintenance Setup Figure A : Portable Air Supply Setup G A E E H B F Non-lubricated Tools Lubricated Tools B A C C D A Description Function A Air Hose Connects air to tool B Filter Prevents dirt and condensation from damaging tool or work piece C Regulator Adjusts air pressure to tool D Lubricator (optional) For air tool lubrication E Coupler and Plug Provides quick connection and release F Leader Hose (optional) Increases coupler life G Air Cleaner / Dryer (optional) Prevents water vapor from damaging work piece H Air Adjusting Valve (optional) For fine tuning airflow at tool Item 93100 For technical questions, please call 1-800-444-3353. Page 9 Maintenance Operation Setup Safety Figure B: Stationary Air Supply Setup N L L O C M C Non-lubricated Tools Lubricated Tools I H I J J K H F G E Slope F F B B A A C D Description Function A Vibration Pads For noise and vibration reduction B Anchor Bolts Secures air compressor in place C Ball Valve Isolates sections of system for maintenance D Isolation Hose For vibration reduction E Main Air Line - 3/4. minimum recommended Distributes air to branch lines F Ball Valve To drain moisture from system G Branch Air Line -1/2. minimum recommended Brings air to point of use H Air Hose Connects air to tool I Filter Prevents dirt and condensation from damaging tool or work piece J Regulator Adjusts air pressure to tool K Lubricator (optional) For air tool lubrication L Coupler and Plug Provides quick connection and release M Leader Hose (optional) Increases coupler life N Air Cleaner / Dryer (optional) Prevents water vapor from damaging work piece O Air Adjusting Valve (optional) For fine tuning airflow at tool Operating instructions Operating instructions SaFEty SEtup OpERatiOn maintEnancE Read the EntiRE impORtant SaFEty inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. inspect tool before use, looking for damaged, loose, and missing parts. if any problems are found, do not use tool until repaired. tO pREVEnt SERiOuS injuRy FROm acciDEntal OpERatiOn: turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle and/or turn the switch to its off position before performing any inspection, maintenance, or cleaning procedures. tO pREVEnt SERiOuS injuRy: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. improper adjustment can result in tool failure or other serious hazards. Work piece and Work area Set up 1. Designate a work area that is clean and well-lit. 3. Secure loose workpieces using a vise or clamps The work area must not allow access by children (not included) to prevent movement while working. or pets to prevent distraction and injury. 4. There must not be hazardous objects 2. Route the air hose along a safe route to reach (such as utility lines or foreign objects) nearby the work area without creating a tripping hazard that will present a hazard while working. or exposing the air hose to possible damage. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. Page 10 For technical questions, please call 1-800-444-3353. Item 93100 General Operating instructions 1. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use. note: Turn off the air compressor and disconnect the air hose when changing sockets. note: Only use impact sockets on this tool. 2. Select the desired size 3/8" drive socket (sold separately). 3. Push the socket onto the Anvil until it clicks into place. 4. Connect the air hose and turn on the air compressor. 5. Adjust the Air Regulator on the Impact Wrench as needed from 1 through 8 to set the amount of torque. 6. If tightening, tighten by hand as much as possible. 7. Position the socket on the Impact Wrench over the fastener/hardware. 8. Grip the Impact Wrench firmly with two hands and rock the Throttle Lever in the direction you want to rotate the fastener/hardware: • To loosen a standard fastener/hardware, press on the left side of the Throttle Lever (Reverse - counterclockwise rotation) • To tighten a standard fastener/hardware, press on the right side of the Throttle Lever (Forward - clockwise rotation). cautiOn! Do not hold the socket during use. 9. When the fastener/hardware is tightened or loosened, release the Throttle. 10. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool. cautiOn! tO pREVEnt injuRy FRO...