Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Set Up Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. ASSEMBLY Mount the Frame (24) to workbench, and make sure it is fastened securely to 1. prevent loosening during use. The Frame can be filled with sand if you wish to help minimize sound and 2. vibration. Figure 1Mini PlanishingHammerAir Inlet (9) Foot Pedal (26)Air Hose (25) 3. Connect the Rubber Air Hose (25) to both the Air Inlet (9) and the Foot Pedal (26). See Figure 1. C4. Figure 2Foot Pedal(26) onnect pneumatic air supply to the Foot Pedal (26). See Figure 2 and Figure 3 on page 8. The air line components listed in Figure 2 are not included as part of this tool but 5. may be purchased at Harbor Freight tools. Be sure to tighten all fittings and connections.6. REV 08a Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Figure 3Air Outlet, connect hose to HammerAir Inlet, connect hose to air compressor The Frame (24) should be positioned so that the mounted Mini Planishing Ham7. mer is extending slightly over the edge of the workbench. This will help to accommodate various shapes being plannished. Screw off the Coil Spring (15) and remove the Anvil Head (21) and Hammer 8. Shank (23) from the Cylinder (14). Slide the Hammer Body (1) into the Frame (24).9. Insert the Anvil Head (21) into the Anvil Shaft (19) and tighten in place with Hex 10. Screw (20). Place the Anvil Head (21) and Hammer Shank (23) into the Coil Spring (15) and 11. screw onto the Cylinder (14). See Parts List and Assembly Diagram on page 11 and 12. Operating Instructions REV 08a Turn on the Air Compressor (not included) and set it to 90 PSI. Do not exceed 1. maximum air pressure of 100 PSI. Before planishing, test the operation by pressing down on the Foot Pedal (26).2. Adjust the cycle speed of the Planishing Hammer by turning the Regulator (4) 3. clockwise or counterclockwise. Using both hands, place the material to be planished between the Anvil Head 4. (21) and the Hammer Shank (23). Press down on the Foot Pedal (26) to opperate planishing action. 5. When finished, remove your foot from the Foot Pedal (26) and wait for the action 6. to stop completely. Turn the air compressor off.7. Press down on the Foot Pedal (26) to release any remaining air pressure within 8. the Planishing Hammer. To prevent accidents, always disconnect the air supply after use. Clean, then 9. store the tool indoors out of children’s reach. OPERATING INSTRUCTIONS Maintenance And Servicing Risk of serious personal injury, unplug the tool from its air supply before performing any inspection, maintenance, or cleaning procedures. Damaged equipment can fail, causing serious personal injury. Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged air hoses, and any other condition that may affect its safe operation. After Use,2. clean external surfaces of the tool with clean, moist cloth. WARNING! If the air hose is damaged, DO NOT attempt to repair it. It must 3. be replaced. WARNING Troubleshooting Problem Possible Causes Probable Solutions Mini Planishing Hammer will not operate when Foot Pedal is depressed. No air pressure in air line. Regulator valve is closed. Check all hoses, connections and make sure the compressor is operating. Turn the valve counterclockwise. Mini Planishing Hammer operates but at diminished pressure. Air Pressure is below normal operating pressure of 90 PSI. Regulator valve is closed. Check Regulator on compressor and Planishing Hammer. Turn the valve counterclockwise. Be sure to follow all manufacturer’s instructions, safety warnings and maintenance procedures in the manual of the air compressor you are using with this Mini Plannishing Hammer. LEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer...