Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
rated as being suitable for use with impact wrenches. - Prolonged exposure to vibration may cause injury. -Read all instructions before using this tool. Ail operators must be fully trained in its use and aware of these safety rules. - Do not exceed the maximum working air pressure. - Use personal protection equipment as recommended. - Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects and other reproductive harm. -Use only compressed air at the recommended conditions. - If the tool appears to malfunction, remove from use immediately and arrange for service and repair. If it is not practical to remove tool from service, then shut off the air supply to the tool and write or have written a warning note and attach it to the tool. - If tool is to be used with a balancer or other suspension device, ensure that the tool is firmly attached to the suspension/support device. - When operating the tool, always keep the body and particularly the hands away from the working attachment fixed to the tool. - The too! is not electrically insulated. Never use the tool if there is any chance of coming into contact with live electricity. -Always when using the tool, adopt a firm footing anchor position and grip the tool sufficiently only to overcome any reaction forces that may result from the tool doing work. Do not overgrip. -Use only correct spare parts for maintenance and repair. Do not improvise or make temporary repairs. Major servicing and repairs should only be carried out by persons trained to do so. - Do not lock, tape, wire, etc. the ‘On/Off’ valve in 'On’ position. The trigger/lever, etc. must always be free to return to the ‘Off” position when released. Aff Pipe And Fittings Should Be 1/2" Or Larger.*. Compressor with Sufficient Capacity To Maintain Recommended Working Pressure At Each Tool Outlet jgb / fiecenr&Tank \ UQ GaUoos Gi More r~~ At J Take Air From Top tow Spot To Trap Water Drain Daily Easy To Reach And Air Tool ^ Operate Shut Off Valve Air Regulator Set At Recommended Working . Air Pressure Filter Lubricator Drain Daily Recommended Atr Supply System Figure 1 Page No 1 - Always shut off the air supply to the tool and press the ‘On/Off’ valve to exhaust the air from the feed hose before fitting, removing or adjusting the working attachment fitted to the tool. - Before using the tool, make sure that a shut off device has been fitted to the air supply line and the position is known and easily accessible so that the air supply to the tool can be shut off in an emergency. - Check hose and fittings regularly for wear. -Take care against entanglement of the moving parts of the tool with clothing, hair, ties, cleaning rags, rings, jewelry, watches, bracelets, etc. This could cause the body or parts of the body to be drawn towards and in contact with the moving parts of the tool and could be very dangerous. -It is expected that users will adopt safe working practices and observe all local, regional and country legal requirements when installing, using or maintaining the tool. - Take care that the exhaust air does not point towards any other person or material or substance that could be contaminated by oil droplets. When first lubricating a tool or if the tool exhaust has a high oil content, do not allow the exhaust air to come near very hot surfaces or flames. - Never lay the tool down until the working attachment has stopped moving. - When the tool is not in use, shut off the air supply and press the trigger/lever to drain the supply line. If the tod is not to be used for a period of time, first lubricate, disconnect from air supply and store in a dry average room temperature environment. -If the tool is passed from one user to a new or inexperienced user, make sure these instructions are passed with the tool. - Do not remove any manufacturer fitted safety devices where fitted, i.e., wheel guards, safety trigger, speed governors, etc. - Wherever possible, secure workpiece with damps, a vise, etc. to make it rigid so it does not move during the work operation. Keep good balance at all times. Do not stretch or overreach. - Try to match the tool to the work operation. Do not use a tod that is too light or heavy for the work operation, tf in doubt, seek advice. -In general terms, this tool is not suitable for underwater use or use in explosive environments—seek advice from manufacturer. - Try to make sure that the work area is clear to enable the work task to be performed safely. If practical and possible, try to dear unnecessary obstructions before starting work. -Always use air hose and couplings with minimum working pressure ratings at least 1 1/2 times the maximum working pressure rating of the tool. Foreseen Use Of The Tool - 5050A/ 5051 A/5050AL The impact wrench is designed tor the tightening and loosening of threaded fasteners within the range as specified by ...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 5050AL (1.28 mb)
Дрели и шуропопверты - 5051A (1.28 mb)