Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
The tool is equipped with a 3-conductor cord and 3-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect the green (or green and yellow) wire to a live terminal. If your unit is intended for use on less than 150 V, it has a plug that looks like that shown in sketch A. If it is for use on 150 to 250 V, it has a plug that looks like that shown in sketch D. An adapter, sketches B and C, is available for connecting sketch A type plugs to 2-prong receptacles. The green-colored rigid ear, lug, or the like, extending from the adapter must be connected to a permanent ground, such as a properly grounded outlet box. No adapter is available for a plug as shown in sketch D. ADAPTER SHOWN IN FIGURES B and C IS NOT FOR USE IN CANADA. A GROUNDED B C D OUTLET BOX GROUNDING MEANS ADAPTER GROUNDING PIN GROUNDING PIN SAVE THESE INSTRUCTIONS Motor Your D EWALT tool is powered by a D EWALT built motor. Be sure your power supply agrees with the nameplate marking. The markings; 120 volts, 50/60 Hz or “AC/DC”, mean that your drill will operate on alternating or direct current.Voltage decrease of more than 10% will cause loss of power and overheating. All D EWALT tools are factory tested; if this tool does not operate, check the power supply. Spade Handle The spade handle is installed as shown in Figure 1. Tighten the two screws securely. NOTE: The spade handle can be removed from the tool if additional working clearance is needed. Always operate drill with side handle or spade handle. Either handle may be removed but never remove both handles at once! Side Handle CAUTION: Always use and hold the side handle or spade handle firmly . This is a high- torque drill, always hold it with both hands when operating. The side handle screws into the large hole in the top of the tool. Switch To turn the tool ON, depress the trigger switch. To turn the tool OFF, release the trigger switch. (See Figure 2). The toggle switch above the trigger is the reversing switch. Switch this toggle only when the tool is not running or coasting. After reversing operations are completed, switch the toggle back to forward position. To lock the tool ON, depress the trigger and push in the lock button. Then, while holding the lock button in position, gently release the trigger. To release locking mechanism, depress trigger fully, then release it. Do not lock the switch ON when drilling by hand so that you can instantly release the trigger switch if the bit binds in the hole. The locking feature is for use when the SPADE HANDLE POIGNEE-BECHE MANGO TIPO ESPADA drill is mounted in a drill stand or otherwise firmly held. THE LOCKING FEATURE IS NOT FOR USE WHEN DRILLING BY HAND. Be sure to release the switch lock button before disconnecting the tool from the power supply. Failure to do so will cause the tool to start immediately the next time it is plugged in. Damage or injury could result. Chuck To insert bit, open chuck jaws by turning collar with fingers and insert shank of bit about 3/4" (19mm) into chuck. Tighten chuck collar by hand. Place chuck key in each of the three holes and tighten in clockwise direction. It’s important to tighten chuck with all three holes. To release bit, turn chuck key counterclockwise in just one hole, then loosen the chuck by hand. Chuck Key Holder NOTE: May be installed already. 1. Push double hole end of holder through slot in other end of holder as shown in Figure 3. 2. Slip loop over electric plug and draw loop tight around cord (Figure 4). 3. Push ends of chuck key handle through two holes in end of holder as shown in Figure 5. Chuck Removal 1. TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. 2. Place chuck key in chuck as shown in Figure 6. 3. Using a wooden mallet or similar object, strike key sharply in a clockwise direction. This will loosen screw inside chuck (Figure 6). 4. Open chuck jaws fully. Insert screwdriver (or 3/16", 5mm, hex wrench if required) into front of chuck between jaws to engage screw head. 5. Remove screw by turning clockwise (left-hand thread). 6. Place key in chuck as shown in Figure 7. 7. Using a wooden mallet or similar object, strike key sharply in a counterclockwise direction. This will loosen chuck so that it can be unscrewed by hand (Figure 7). Drilling 1. Always turn off tool and disconnect from power supply when attaching or changing bits or accessories. 2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use high speed steel twist drill bits or hole saws. For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits 3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a “back-up” block to prevent damage to the material. 4. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit biting, but do not push hard enough to stall ...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - DW131 (409.01 kb)