Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
(APR97-CD-1) Form No. 383945 DW100-220 Copyright © 1997 383945/5/3/02 1:15 Page 3 INSTRUCTIVO DE OPERACION, CENTROS Y POLIZA INSTRUCTION MANUAL DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. GUIDE D'UTILISATION MANUAL DE INSTRUCCIONES DW100-220 3/ 8" V.S.R. Drill Perceuse de 10 mm (3/8 po) a regulateur de vitesse et inverseur de marche Taladro V.V. R. de 10 mm (3/8") 383945/5/3/02 1:15 Page 4 Double insulated tools are constructed throughout layers of electrical insulation or one double between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. tool is equipped with a two prong plug which permits extension cords without concern for maintaining a ground connection. Double Insulation personal injury, including the following: should always be followed Important Safety English IF YOU HAVE ANY QUESTIONS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) BELT CLIP WARNING: When using electric tools, READ ALL INSTRUCTIONS NOTE: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is added protection against injury resulting from a possible electrical insulation failure within the tool. CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or replace damaged cords. Safety Instructions For All Tools • KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. • CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t use power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence of flammable liquids or gases. • GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, and refrigerator enclosures. REVERSING LEVER TRIGGER SWITCH LOCKING BUTTON LANYARD RING 220 VOLT PLUG 383945/5/3/02 1:15 Page 1 English • KEEP CHILDREN AWAY. Do not let visitors contact extension cord. All visitors • STORE IDLE TOOLS. When not in use, tools should dry, and high or locked-up place • DON’T FORCE TOOL. It will do the job better and safer rate for which it was intended. • USE RIGHT TOOL. Don’t force small tool or attachment job of a heavy-duty tool. Don’t use tool • DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves footwear are recommended when working outdoors. protective hair covering to contain long hair. • USE SAFETY GLASSES. Also use face or dust mask if operation is dusty. • DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and edges. • SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool. • DON’T OVERREACH. Keep proper footing and balance at all times. • MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. • DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when changing accessories, such as blades, bits, cutters. • REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 1 • AVOID UNINTENTIONAL Don’t carry tool with on switch. Be sure switch • EXTENSION CORDS. Make sure your extension condition. When using an extension heavy enough to carry the current An undersized cord will cause a drop of power and overheating. The following size to use depending on cord length rating. If in doubt, use the next heavier number, the heavier the cord. Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more Than Than AWG 0 6 10 12 ---- 6 10 12 16 18 18 16 14 16 16 16 12 16 14 14 12 14 12 Not Recommended • OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. • STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired. • CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service 383945/5/3/02 1:15 Page 2 English center. Do not use tool if • CAUTION: When drilling or...