Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
USE A GOOD GRADE OF PLYWOOD WITH A MINIMUM 3/4" THICKNESS. DO NOT MAKE THE MOUNTING BOARD FROM PARTICLE BOARD SINCE PARTICLE BOARD BREAKS EASILY. 2. Use a plywood board base, with the minimum dimensions as shown in Fig. 4 for mounting the drill press base to a supporting surface. 3. Place the drill press base (D) Fig. 5, centered on the supporting surface (E). MAKE SURE THERE IS AT LEAST 3" ON ALL FOUR SIDES OF THE BASE AS SHOWN IN FIG. 5. 4. Drill two 3/8" diameter holes through the holes (A) Fig. 3 in the drill press base, and in the supporting surface (E) Fig. 5. Fig. 4 A Fig. 3 PLACE A PIECE OF SCRAP WOOD UNDERNEATH THE SUPPORTING SURFACE WHEN DRILLING THE THROUGH HOLES SO THAT THE DRILL BIT WILL NOT DAMAGE THE MATERIAL BENEATH THE SUPPORTING SURFACE. 5. Fasten the drill press base to the mounting board using the carriage bolts, flat washers, lockwashers, and hex nuts (C) Fig. 4, furnished with your drill press. The holes for the carriage bolt heads must be countersunk so that the bolt heads are flush or below the bottom surface of the mounting board. Fig. 5 3" MINIMUM 3" MINIMUM 3" MINIMUM 3" MINIMUM D E THE PLYWOOD BASE MUST BE SECURED TO THE FLOOR OR SUPPORTING SURFACE IF THERE IS ANY TENDENCY OF THE DRILL PRESS TO VIBRATE, SLIDE OR WALK DURING NORMAL OPERATION. 8 6. Assemble the column (A) Fig. 6, to the base (B) using the four M10x40mm hex head screws (C), three of which are shown. Fig. 6 C C A B 7. Assemble table raising and lowering handle (D) Fig. 7, to worm gear shaft (E) and tighten screw (F) against flat on shaft with 3mm wrench supplied. D E F Fig. 7 8. Thread table clamp handle (G) Fig. 8, into hole in rear of table bracket, as shown. G Fig. 8 9 9. Insert table (H) Fig. 9, into hole in table bracket as shown. 10. Thread table locking lever (J) Fig. 10, into hole in front of table bracket as shown. 11. Place the drill press head (K) Fig. 11, onto the column as far as it will go. Align head (K) Fig. 12, with table (L) Fig. 12, and base (M) Fig. 12, and tighten the two head locking screws (N) Fig. 11 with the 5mm wrench supplied. H Fig. 9 J Fig. 10 12. IMPORTANT: Make certain the tapered hole in the bottom of spindle (T) Fig. 13, and the taper on spindle adapter (U) are clean and free of any grease, lacquer or rust preventive coatings. NOTE: If necessary, household oven cleaner can effectively remove these coatings from the spindle and spindle adapter; however, carefully follow the manufacturer’s safety rules regarding its use. 13. Push spindle adapter (U) Fig. 13, up into spindle (T) making certain the tang (V) engages the mating slot inside spindle (T). K N Fig. 11 T U V K L M Fig. 12 Fig. 13 10 14. IMPORTANT: Make certain the spindle taper (O) Fig. 14, and tapered hole in chuck (P) are clean and free of any grease, lacquer or rust preventive coatings. NOTE: Household oven cleaner can effectively remove any substance from the chuck; however, carefully follow the manufacturer's safety rules concerning its use. 15. IMPORTANT: OPEN THE CHUCK JAWS AS WIDE AS POSSIBLE MAKING SURE THE CHUCK JAWS ARE INSIDE THE CHUCK. O P Fig. 14 16. Holding chuck on taper of spindle, tap with a soft tip hammer (Q) or a block of wood and hammer to set chuck, as shown in Fig. 15. To avoid damage to the chuck, NEVER drive the chuck onto the spindle with a metal hammer. Q Fig. 15 17. Thread the three pinion shaft handles (R) into the three holes located in the pinion shaft hub (S), as shown in Fig. 16. Fig. 16 R R S 11 18. Align the two holes in the lamp bracket (A) Fig. 17, with the two holes (B) on the side of the drill press head. 19. Place the cord bushing (C) Fig. 17, around the top of the lamp cord (D). A B C D Fig. 17 20. Align the two holes in the lamp cord bracket (F) Fig. 18 with the two holes in the lamp bracket (A) and drill press head. 21. Place a 1/4" washer onto a M6x1x12mm cap head screw. Insert the screw (G) Fig. 18 through the hole in the cord strain relief bracket and the lamp bracket and thread the screw into the drill press head. Repeat this process for the remaining hole in the cord strain relief bracket and tighten both screws securely. Fig. 18 F A G 22. Peel backing from cord clamp (H) Fig. 19, and apply clamp at the location shown. Make certain the lamp cord is routed out of the way of the drill, then secure cord (J) to cord clamp (H) as shown in Fig. 19. H J Fig. 19 12 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING DRILL PRESS The switch (A) Fig. 20, is located on the front of the drill press head. To turn the drill press “ON” move the switch up to the “ON” position. To turn the drill press “OFF” move the switch down to the “OFF” position. A Fig. 20 LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig. 21. With the switch toggle (B) removed, the switch will not operate. However, ...