Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Havis-Shields, модель Interior Window Guards F2

Производитель: Havis-Shields
Размер: 1.75 mb
Название файла: f5593c0c-7392-4744-a92e-c92181102719.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Remove seats and seat belts for better access to the windows. 2. Remove plastic trim surrounding the fixed body windows. Save the plastic trim for reinstallation. 3. Determine which guard goes to each window. NOTE: The perforated diamond shaped holes has one side that is smoother than the other. The smoother side goes towards the inside, facing the passenger. DOOR WINDOW GUARDS: 1. In order for guard to fit properly on frame, you must permanently remove the upper plastic trim on doors. The top of the lower door panel may have to be trimmed approximately .” to .”. (Note: Place guard on window frame to determine possible trimming). See section 8 – door window guard does not have cutouts for window latches (making them inoperable). 2. With the doors open, hold the window screen up to the window/door frame. The guard framework should fit evenly around the window frame. 3. Mark a few holes at the top of the door frame using the predrilled holes on the screen framework as a guide. Do not mark holes for the sides or bottom yet. 4. Put on Safety goggles. 5. Remove window guards and drill holes as marked with a 1/8” drill bit. 6. Attach window screens by using #10 x .” sheet metal screws. Now locate and mark the balance of holes, drill and attach, starting at the top and work your way down. 7. If vehicle has plastic upper door trim, do not reinstall. WGI-F1-F2-F3-F4_INST_7-08 SIDE SLIDING DOOR WINDOW GUARD (F2-10): 1. A 14” long aluminum angle bracket is provided to attach to the rear vertical section of the window frame. 2. This is necessary in order to screw on the rear vertical section of window guard. 3. Using four (4) #10 x .” Sheet metal screws, attach angle bracket to frame through existing bracket holes. • The side of the bracket without holes should be flush with the inside of the window frame. • The window guard can now be installed as stated in section #4. See section 8 – door window guard does not have cutouts for window latches (making them inoperable). FIXED BODY WINDOW GUARD: 1. While holding the cage in place, drill 1/8” pilot holes for mounting screws. 2. Install using #10 x .” sheet metal screws provided. NOTE 1: Be careful not to drill into glass. (Use drill stop) NOTE 2: To avoid stripping of holes, do not over tighten. NOTE 3: Some of the trim mounting spring clips may need to be removed to allow screens to meet the window frame easily. PLASTIC WINDOW TRIM INSTALLATION: 1. Plastic Trim Spacing: • Plastic trim must be spaced out .” to accommodate window guard. • Remove the top screws from the lower trim panels. (These panels should still be in the van). • Pull out the lower panel just enough to insert the .” nylon Spacers provided with the kit. • Screw the top of the lower trim panels back on with #10 x 1 .” sheet metal screws also provided with the kit. 2. Metal Spring Clip Spacing: • (See diagram 1 on page 4) There are metal spring clips that hold the upper trim in place. These clips must also be spaced out using the following method...

Эта инструкция также подходит к моделям:
Дрели и шуропопверты - Interior Window Guards F2 (1.75 mb)
Дрели и шуропопверты - Interior Window Guards F3 (1.75 mb)
Дрели и шуропопверты - Interior Window Guards F4 (1.75 mb)
Дрели и шуропопверты - Interior Window Guards WGI-F1 (1.75 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории