Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
¦ Make sure the latches on each side of your battery pack snap in place and that battery pack is secured in drill before beginning operation. TO REMOVE BATTERY PACK ¦ Place the direction of rotation selector in center position. See Figure 10. ¦ Locate latches on side of battery pack and depress both sides to release battery pack from your drill. See Figure 13. ¦ Remove battery pack from your drill. CAUTION: When placing battery pack in your drill, be sure raised rib on battery pack aligns with groove in drill's battery port and latches snap in place properly. Improper assembly of battery pack can cause damage to internal components. BIT STORAGE See Figure 14. When not in use, the bit provided with this drill can be placed in the storage area located on the base of the drill. ELECTRIC BRAKE This drill has an electric brake. When the trigger switch is released, the chuck stops turning. When the brake is functioning properly, sparks will be visible through the vent slots on the housing. This is normal and is the action of the brake. DEPRESS LATCHES TO RELEASE BATTERY PACK BATTERY PACK BATTERY PORT LATCHES BIT STORAGE AREA SCREWDRIVER BIT Fig. 13 Fig. 14 Page 16 OPERATION WARNING: Always wear safety goggles or safety glasses with side shields when operating tool. Failure to do so could result in dust, shavings, or loose particles being thrown into your eyes, resulting in possible serious injury. DRILLING See Figure 15. The material to be drilled should be secured in a vise or with clamps to keep it from turning as the drill bit rotates. Hold tool firmly and place the bit at the point to be drilled. Depress the switch trigger to start tool. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force or apply side pressure to elongate a hole. We recommend that you select normal drill mode when drilling with twist drills, hole saws, etc., in soft material. WARNING: Do not force tool. Forcing tool can result in jamming and loss of balance or footing, which could result in personal injury. When drilling hard, smooth surfaces, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off center as the hole is started. However, the lower speed feature allows starting holes without center punching if desired. To accomplish this, simply operate your drill at lower speed until the hole is started. For drilling in wood, begin drilling at LO (1) speed, gradu- ally increasing to full power. Occasionally clear chips from the bit to prevent overheating. Low speed bits should be used when drilling larger holes. When drilling metals other than brass and cast iron, use a light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action. Begin drilling at LO (1) speed, gradually increasing to higher speeds. When drilling larger holes in steel, it may be helpful to first drill a smaller pilot hole. We recommend that you use carbide-tipped bits and select hammer mode when drilling in hard materials such as brick, tile, concrete, etc. This tool is packed with two double-ended screwdriver bits. For driving screws, select the desired speed and torque settings using the speed selector and torque adjustment ¦ Hold the drill at a right angle as shown in figure 15. Do not force or apply side pressure to elongate the hole. ¦ If the hammer speed decreases while drilling deep holes, it may be necessary to lift up partially on the tool to clear debris from the hole. ¦ If there is excessive dust while using the hammer feature, do not add water to the hole. This can cause clogging and binding of the bit. ¦ If the bit jams in workpiece or if the drill stalls, release switch trigger immediately. Remove the bit from the workpiece and determine the reason for jamming. WARNING: Be prepared for binding or bit breakthrough. When these situations occur, the drill has a tendency to grab and kick opposite to the direction of rotation, and could cause loss of control when breaking through material. If you are not prepared, this loss of control can result in possible serious injury. Fig. 15 OPERATION WARNING: Always wear safety goggles or safety glasses with side shields when operating tool. Failure to do so could result in dust, shavings, or loose particles being thrown into your eyes, resulting in possible serious injury. DRILLING See Figure 15. The material to be drilled should be secured in a vise or with clamps to keep it from turning as the drill bit rotates. Hold tool firmly and place the bit at the point to be drilled. Depress the switch trigger to start tool. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force or apply side pressure to elongate a hole. We recommend that you select normal drill mode when drilling with twist drills, hole saws, etc., in soft material. WARNING: Do not force tool. Forcing tool can result in jamming and loss of bala...