Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
2. CHARGE ONLY USING THE SUPPLIED CHARGER AND BATTERY. Do not use with other batteries, chargers or drills. 3. DO NOT EXPOSE BATTERY OR CHARGER TO WET OR RAINY CONDITIONS. Moisture greatly increases the risk of a shock hazard. 4. DO NOT TOUCH BATTERY POLES with any conductive materials. Touching any two poles at the same time causes a short condition and can cause sparks, electrical shock or fire. 5. DO NOT STORE BATTERY WITH CONDUCTIVE MATERIALS. Storing the battery in a box of screws or nails can cause shorting across the battery poles. 6. DO NOT THROW BATTERY IN FIRE. Combustion of some of the batteries’ component materials can cause toxic fumes and possible explosion. 7. IF CHARGER LIGHT FAILS TO COME ON check the incoming power supply. If power source is okay, then the fuse inside the charger needs replacement. Charger should be serviced by a qualified electrical technician only. 8. CHARGER HAS A POLARIZED PLUG (one prong is wider than the other). Do not attempt to modify the plug. Modifying the plug will result in a safety hazard and will void the warranty. 9. CHARGER IS DESIGNED TO OPERATE AT 110-120 VOLTS. Never try to plug into any circuit that is not 110-120 volts. Never modify or change the plug that is attached to the charger unit to attempt to plug into 220 volt. This can cause serious electrical damage to the unit, possible fire or explosion. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. Consult your local Yellow Pages directory under the category “Recycling” to locate a battery recycler in your area. -5- G8595 14.4V Cordless Drill BEFORE YOU START First review the contents of your cordless tool kit and familiarize yourself with the key components. Figure 1 shows the contents of the kit: Heavy-Duty Case Cordless Drill Battery Pack AC Adapter Charging Stand Bit Extension 6 pc Twist Drill Set 6 pc Screwdriver Bit Set Double End Phillips®/Straight The battery in your new cordless power tool will not be fully charged when you receive it. To maximize the storage capacity of the battery it should be completely discharged, then fully recharged 3-5 times. For optimal life span, completely discharge the battery before recharging. Follow the instructions below to charge your battery. Battery charging with the standard charger (2 piece charger): 1. Plug the AC adapter into the 110/120V outlet. 2. Plug the pin jack from the AC adapter into the charging base. 3. Insert the battery into the charger. The battery fits into the oval recess in only one way. Do not force the battery. Insert until it locks into place. 4. The red LED light on the charging unit will come on when the battery begins its charging cycle. 5. Charge battery for 3-5 hours for a full charge from a fully depleted condition. The red LED will not go off until the battery is removed from the charger base. Fig1. Cordless tool kit contents. Never leave a battery unattended while charging. While charging will make the battery and charging unit warm, if it becomes hot to the touch, disconnect the charger immediately. There is a possibility of fire hazard. Have the battery and charging unit checked by a qualified electrical service technician. G8595 14.4V Cordless Drill -6 OPERATION Inserting Battery Into Drill 1. Insert the battery into the handle of the drill so that the long end is forward. The battery will only install in one orientation. 2. Make sure the securing clasps on either side of the drill base engage with the clips on the battery compartment. Inserting and Removing Bits and Drivers: 1. Set the direction switch, located just above the trigger, so that it is in the center locked position. 2. Hold the chuck by the collar while turning the sleeve (the forward section). This will cause the three chuck jaws located inside the recess to open or close depending upon the direction. 3. When the jaws are at the approximate diameter of the bit or driver, insert the shank end of the bit or driver into the jaw opening. 4. Turn the sleeve clockwise until it tightens around the bit or driver. Never “power tighten” which is holding the sleeve while running the drill. This can cause a loose grip on the bit or driver and potential damage to chuck jaws. Check for tightness periodically while using the tool. 5. To release the bit or driver, hold the chuck collar, and turn the sleeve counterclockwise. Fig 2. Inserting bits into the chuck. Operating this equipment has the potential to propel debris into the air which can cause eye injury. Always wear safety glasses or goggles when operating equipment. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI). -7- G8595 14.4V Cordless Drill OPERATION, CONT’D Operating the drill 1. Set the Direction Switch for the desired rotation of the bit or driver. The direction switch is the sliding switch located just above the trigger. When looking down on the drill, pushing the switch all the way to the right will give a counterclockwise rotation (nor...