Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Always wear: •Approved protective helmet •Approved hearing protection •Protective goggles or a visor •Breathing mask This product is in accordance with applicable EC directives. Environmental marking. Symbols on the product or its packaging indicate that this product cannot be handled as domestic waste. It must instead be submitted to an appropriate recycling station for the recovery of electrical and electronic equipment. By ensuring that this product is taken care of correctly, you can help to counteract the potential negative impact on the environment and people that can otherwise result through the incorrect waste management of this product. For more detailed information about recycling this product, contact your municipality, your domestic waste service or the shop from where you purchased the product. Ensure that water cannot leak into the machine when drilling in the ceiling. Use an appropriate water collector. Other symbols/decals on the machine refer to special certification requirements for certain markets. Symbols in the operator’s manual: Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected. Always wear approved protective gloves. Regular cleaning is required. Visual check. Protective goggles or a visor must be worn. Contents KEY TO SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 PRESENTATION DM 340 ........................................................................ 4 WHAT IS WHAT? What is what on the drilling machine? ......................... 5 SAFETY INSTRUCTIONS Steps before using a new drilling machine .................. 6 Personal protective equipment ..................................... 6 General safety precautions .......................................... 7 General working instructions ....................................... 8 Machine.s safety equipment ........................................ 9 STARTING AND STOPPING Before starting ............................................................. 10 Starting ........................................................................ 10 Stopping ....................................................................... 10 MAINTENANCE General ........................................................................ 11 Changing the drill bit .................................................... 11 Cleaning ....................................................................... 11 Electrical Feed ............................................................. 11 Changing the gearbox oil ............................................. 11 Replacing the carbon brushes ..................................... 12 Replacing the seal retainer .......................................... 12 Daily maintenance ....................................................... 12 Repairs ........................................................................ 12 TECHNICAL DATA EC-declaration of conformity ........................................ 14 WIRING DIAGRAM DM 340 It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator.s manual as a valuable document. By following its. content (using, service, maintenance etc) the life span and the second-hand value of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator.s manual. A purchase of one of our products gives you access to professional help with repairs and services. If the retailer who sells your machine is not one of our authorised dealers, ask him for the address of your nearest service workshop. Husqvarna Construction Products has a policy of continuous product development. Husqvarna reserves the right to modify the design and appearance of products without prior notice and without further obligation introduce design modifications. •DM 340 is an electric stand drill, intended for drilling holes in concrete, bricks and various stone materials. •The drilling machine has a modular design and is easy to assemble. •The machine is equipped with a water connection which can be rotated 180 degrees to facilitate work. •DM 340 has three speed ranges for drill bit sizes up to 400 mm. •The machine has a water cooled gearbox with a pipe that runs through the spindle. •The machine is equipped with LEDs which indicate the power output. This way you can always get maximum power output without damaging the machine. The drilling machine is equipped with SoftstartTM, SmartstartTM, ElgardTM and speed control. SoftstartTM SoftstartTM is an electronic current limiter which provides a softer start. Maximum speed is reached about three seconds after the machine is turned on. SmartstartTM If the SmartstartTM button is pressed in the speed is reduced. In SmartstartTM mode the m...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - DM 340 (540.2 kb)