Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
No. 48-66-0061) on other FUNCTIONAL DESCRIPTION 1. Drive shank 2. Forward/Reverse switch 3. Trigger 4. Battery pack 5. Battery pack release buttons 6. Quick change chuck (Cat. No. 9098-23 and 9099-20) 7. Tool hanger (Cat. No. 9098-23 and 9099-20) 8. Tool hanger ring (Cat. No. 9098-23 and 9099-20) 4 3 2 1 5 Cat. No. 9079-20 Cat. No. 9099-20 7 8 6 Cat. No. 9078-20 1 4 5 1. To attach a socket or other accessory, ASSEMBLY align the hole in the accessory with the detent pin on the drive shank. Hold the detent pin in while pushing the socket WARNING Always lock trigger or remove battery pack before changing or removing accessories. Only use accessories specifically recom-mended for this tool. Others may be hazardous. WARNING Recharge only with the charger specified for the battery pack. For specific charging instructions, read the operator's manual supplied with your charger and battery pack. 2. For optimum weight distribution and onto the drive shank. The detent pin will balance. snap into place in the hole to secure the Insert the battery pack from the back socket. by pressing in the release buttons and 2. To remove the accessory, insert a nail sliding the battery pack into the body of or other thin object into the hole in the the tool (Fig. 2). Insert the battery pack accessory and press the detent pin in. until clamp engages. Pull the accessory off the drive shank. Attaching and Removing Accessories Cat. No. 9098-23, 9099-20, or other Impact Wrenches using the Quick Change 1/2" Square Drive to 7/16" Hex Adapter Cat. No. 9099-20 and accessory Cat. No. 48-66-0061 are intended for use with drill bits and adapters with a 7/16" Hex Quick Change shank. Cat. No. 9098-23 is intended for use with drill bits and adapters with a 5/8" Hex Quick Change shank. Both Hex Removing Battery Pack from Tool WARNING Use only sockets and other acces-sories specifically designed for use on impact wrenches and drivers. Other sockets and accessories might shatter or break causing injury. Quick Change shanks have a ball-retainer groove. They are not intended for use with Push in the release buttons and remove the Hex Shank Bit Extensions. battery pack. Inserting Battery Pack into Tool Battery pack can be inserted into the tool in two ways. Fig. 3Gear case screws Tool hanger Ring Attaching and Removing Accessories 1. For working in restricted spaces. (Cat. No. 9079-20) Insert the battery pack from the front This impact wrench is intended only for use by pressing in the release buttons and with sockets designed for impact wrenches sliding battery pack into the body of the and that have a 1/2" square drive. Other tool (Fig. 1). Insert the battery pack until sockets could shatter or break, causing clamp engages. injury. 1. To attach, remove the two top gear case Fig. 5 Drive shank Detent pin 1. To attach an accessory, pull the chuck screws (Fig. 3). collar forward and insert the accessory 2. Place the ring through the tool hanger. shank. Release the collar. It may be 3. Position the tool hanger on the tool over necessary to pull the bit out slightly to the two gear case screw holes. engage the holding mechanism. 4. Replace the two gear case screws. 2. To remove the accessory, pull the chuck Hand tighten the screws. collar forward and remove the accessory. Release the collar. 5. To remove, reverse the procedure. Attaching and Removing Accessories (Cat. No. 9078-20) This impact wrench is intended with sockets designed and that have a 3/4" sockets could shatter injury. Fig. 4 Drive shank 1. To attach a socket or other accessory, push the accessory onto the drive shank until it snaps into place. 2. To remove the accessory, pull it off the drive shank. Fig. 2 Attaching and Removing the Tool Hanger (Cat. No. 9098-23, 9099-20 or as an accessory) Fig. 6 Open (Release) Closed (Locked) Ball-retainer groove Fig. 1 6 7 OPERATION WARNING When tool is not in use, lock trigger to prevent the tool from being accidentally turned on. Using the Forward/Reverse Switch The forward/reverse switch may be set to three positions: forward, reverse and lock. Due to a lockout mechanism, the forward/ reverse switch can only be adjusted when the trigger is not depressed. Always allow the motor to come to a complete stop before using the forward/reverse switch. 1. For forward (clockwise) rotation, push the forward/reverse switch in the direction shown. Check the direction of rotation before use. 2. For reverse (counterclockwise) rotation, push the forward/reverse switch in the direction shown. Check the direction of rotation before use. Fig. 8 Forward Reverse Forward/ Reverse switch WARNING To reduce the risk of injury, keep hands and away from the bit and all moving parts. Fig. 7 WARNING To reduce the risk of explosion, electric shock and property damage, always check the work area for hidden pipes and wires before drilling. WARNING To reduce the risk of injury, only grasp tool by handle and red insulated surfaces (Fig. 8). Do not hold gray gear case when impacting or ...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 9098-23 (240.2 kb)