Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
• In the working mode, press to display the clock for a while. • In the standby mode, press and hold to set the clock. 17 VOL +/– • Use to set the listening volume. 18 MUTE • Use to mute or restore volume. 19 PTY/ASPM (European model only) • Search for RDS program types. • Press and hold to search for the RDS auto station program memory. 20 RDS (European model only) • Display the available information of an RDS radio station. English 11 En Connections03 Connections03 Chapter 3: Connections Connect speakers Note • For the best sound quality, use the supplied speakers only. • Connect speakers with the same or higher impedance only. Refer to Additional information > Specifications for details. • To avoid magnetic interference or unwanted noise, never place this product too close to any radiation devices. FM antenna installation Note • The antenna on the back panel is used to improve reception of FM. Extend this antenna and fix it to a position with the best reception. • Never tug strongly on the antenna line since damage of an antenna may be caused. • This product does not support MW (medium wave) radio reception. AC IN L R L R SPEAKER 8 FM ANT. FM ANT. Connect power Note • Before you connect the AC power cord, make sure that you have completed all other connections. Connect the AC power cord to •the AC IN~ socket on the back panel, and • the wall outlet. AC IN L R L R SPEAKER 8 FM ANT. U.S. and Canadian model European model To the wall outlet AC IN L R L R SPEAKER 8 FM ANT. Connect the speaker cable plugs to the SPEAKER OUT sockets. • the left one to the L+/L– socket • the right one to the R+/R– socket En Getting started 04 Getting started 04 Chapter 4: Getting started CAUTION • Use of controls or adjustments or performance of procedures other than herein expressly specified may result in hazardous radiation exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. Turning on . Press .STANDBY/ON This product switches to the last selected source. APS mode • After this product is kept inactive for 15 minutes, it automatically switches to the standby mode. – The clock is displayed. – If the clock is not set, [--:--] blinks. How to turn off the APS mode: • Press and hold . to turn off the APS mode in the standby mode and [APS OFF] is displayed. • If the APS mode is turned on again, Press and hold . in the standby mode and [APS ON] is displayed. Note • When an iPod/iPhone is connected, the light of the main display stays on even if it automatically switches to the standby mode. Setting the clock Note • During setting, if no action is made within 90 seconds, the system exits clock setting without saving earlier operations. 1 In the standby mode, press and hold DISPLAY/CLOCK to activate clock setting. The hour digits blink. 2 Press ./. to set the hour, and then press DISPLAY/CLOCK to confirm. The minute digits blink. 3 Press ./. to set the minute, and then press DISPLAY/CLOCK to confirm. Selecting a source Press INPUT repeatedly to select a source. •[DISC]: the disc in the disc tray •[USB]: .wma/.mp3 files stored on the connected USB storage device •[iPod]: the playlist on the connected iPhone/iPod (X-EM21 only) •[FM ST]/[FM MONO]: the FM radio •[AUX IN]: the audio input through the AUX IN socket English 13 En Playing Playing Chapter 5: Playing Playing a disc 1 Press DISC on the remote control or INPUT repeatedly on the main unit to switch the source to [DISC]. 2 Press .to eject the disc tray. 3 Load a disc with the printed side facing up. 4 Press .again to close the disc tray. Playback starts automatically after a few seconds. • If playback does not start automatically, press .to start playback. Playing from a USB storage device This system can play .mp3 and .wma files that are copied onto a supported USB storage device: • Flash drive • Memory card reader • HDD: hard disk drive (This product can detect only a portable HDD with USB power peak current no more than 500 mA.) Note • Pioneer does not guarantee compatibility with all USB storage devices. • NTFS (New Technology File System) file system is not supported. 1 Connect the USB storage device to the USB socket. 2 Press USB on the remote control or INPUT repeatedly on the main unit to switch the source to [USB]. Playback starts automatically. If playback does not start automatically, 1 Press ./. to select an album. 2 Press ./. to select a track. 3 Press . to start playback. Controlling playback During playback, follow the instructions below to control playback. Buttons Functions . Pause or resume playback. . Stop playback. ./. Skip to the previous or next track. Press and hold to rewind a track or search forward fast within a track. ./. Skip to the previous or next album when no less than one album exists. Numeric buttons (0 to 9) Enter the number of a track to play it. MODE Select an available play mode. • Repeat 1 : repeat the current track • Repeat all : repeat all tracks • Repeat album : repeat the current album (only USB ...
Эта инструкция также подходит к моделям:Домашние кинотеатры - X-EM21 (8.74 mb)