Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Домашние кинотеатры - RHT-G900 (2.77 mb)
Домашние кинотеатры - RHT-G900 (4.17 mb)
Домашние кинотеатры - RHT-G900 (845.22 kb)
Фрагмент инструкции
Doing so may cause a malfunction. • If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. 8GB Setting this stand Installing the top glass panel Refer to “How to install the top glass panel” supplied with this stand. Preventing the TV from toppling over As a protective measure, secure the TV. Perform following steps as a protective measure if you have a Sony LCD TV. (large) (small) 1 Place the TV on the center of the stand. Install the TV so that the TV does not hide the top panel display of the stand. 2 Fasten the support belt (supplied) to the stand with the small screw (supplied). Tighten the screw upward into the underside hole, as in the illustration. 3 Fit the support belt to the stand, then firmly fasten with the large screw (supplied) using a screw driver or coin, etc. 4 While supporting the TV, tighten the support belt to secure in place. Installing the shelf board (RHT-G900 only) 1 Insert the attaching shelf support pins (supplied) into the holes in the stand. 2 Fit the shelf board onto the shelf support pins horizontally. This requires people. Getting Started continued 9GB Connecting the FM wire Bundling the cables antenna (aerial) 1 Connect the components to the stand. Connect the FM wire antenna (aerial) to the For details, refer to pages 11 to 15. 75 . COAXIAL jack. 2 Bundle the cables with the cord Notes BD IN DVD IN SAT IN TV OUT FM ANTENNA 75 COAXIAL HDMI FM wire antenna (aerial) (supplied) 75 . COAXIAL jack • Be sure to fully extend the FM wire antenna (aerial). • After connecting the FM wire antenna (aerial), keep it as horizontal as possible. manager to prevent them from tangling. Stuff the cables into the cord manager as shown in the illustration below. Installing this stand Install the stand after connecting all the components to the stand. Install the stand after allowing for a space of more than 5 cm from the wall. This is to allow for heat dissipation and to prevent the TV from falling. More than 5cm Tip Note • If you have poor FM reception, use a 75-ohm coaxial • Be careful not to pinch your fingers when setting up cable (not supplied) to connect the control unit to an the stand. outdoor FM antenna (aerial) as shown below. Outdoor FM antenna (aerial) FM ANTENNA 75 COAXIAL Rear of the stand 10GB Connecting components with HDMI jacks We recommend that you connect components to the stand using an HDMI cable. With HDMI, you can easily enjoy both high quality sound and high quality images. However, it is necessary to connect the audio output of the TV to the audio input of the stand using an optical cable or an audio cord in order listen to the TV’s sound from the stand. For details on the Control for HDMI function, refer to ““BRAVIA” Sync Features” (page 27). Connect the AC power cord (mains lead) after you have finished connecting all components to the stand. Getting Started R TV DMPORT BD IN DVD IN SAT IN TV OUT FM ANTENNA 75 COAXIAL L OPTOPTCOAX OPT ANALOG INPUT HDMI DVD SAT DC 5V 0.7A MAX TV monitor, projector, etc. Audio signal Audio/video signal AAudio/video signal CBAAAAudio/video signal Audio/video signal Blu-ray Disc player (recorder), “PlayStation 3” DVD player (recorder) Satellite tuner : Signal flow A HDMI cable (not supplied) or B Optical cable (supplied) C Audio cord (not supplied) continued 11GB Notes Notes • Refer to page 13 for how to connect a component without an HDMI jack. • The HDMI jack has priority when you connect the component to the stand using INPUT OPT, INPUT COAX and HDMI together. • The INPUT OPT jack has priority when you connect both the audio output of the TV to the INPUT OPT and INPUT ANALOG jack of the stand. Notes on HDMI connections • You can enjoy high quality images using an HDMI cable with an HDMI logo. We recommend that you use a Sony HDMI cable. • Check the setup of the connected component if an image is poor or the sound does not come out of a component connected via the HDMI cable. • Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected component. • Sound may be interrupted when the sampling frequency or the number of channels of audio output signals from the playback component is switched. • When the connected component is not compatible with copyright protection technology (HDCP), the image and/or the sound from the HDMI TV OUT jack may be distorted or may be not output. In this case, check the specification of the connected component. • We do not recommend using an HDMI-DVI conversion cable. • No matter what input is selected for the stand, video signals from the HDMI input jack (BD, DVD or SAT) that was selected last time are output from the HDMI TV OUT jack. 12GB Connecting components without HDMI jacks When you connect a DVD player (recorder), this stand using the INPUT COAX jack. In this satellite tuner, “PlayStation 2”, etc., that has no case, it is not necessary to connect a...
Эта инструкция также подходит к моделям:Домашние кинотеатры - RHT-G1500 (1.43 mb)