Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
D Surround left speaker (L)/ E Surround right speaker (R): Place these speakers behind your listening position, facing slightly inwards. F Subwoofer: The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reflections. G Unit 13 A B D E F A A A A A G C LED indicator of Wireless Receiver BLUE The Wireless Receiver is receiving the signal of the Wireless transmitter. LED color Operation Initial Setting an ID of Wireless ON Wireless Receiver RED The Wireless Receiver is in standby mode. OFF (No display) The Wireless Receiver is turned off. 1 Connect the Wireless Receiver and the rear speaker (right, left) with the speaker cables.: - 2 Connect the power cord of the Wireless Receiver to the outlet.: - 3Turn on the main unit and Wireless Receiver: The main unit and wireless receiver will be automatically connected. “zz” appears in display window POWER Switch Setting an ID of Wireless 1Turn on the main unit and Wireless Receiver: POWER Switch 2 Press and hold STOP(x) on the front of unit and MUTE on the remote control. “REMATE” appears in display window. - 3Turn off the Wireless Receiver: POWER Switch 4Turn on the Wireless Receiver: A new ID is set. POWER Switch When the unit is manufactured, the ID is already set. If an interference occurs or you use a new Wireless Receiver, an ID should be set again. ON Wireless Receiver Be careful of the following If there is a strong electromagnetic wave product nearby, interference may occur. Put the unit (Wireless Receiver and main unit) away from there. (Ex: Microwave oven) If there is no audio signal for longer than 10 minutes, the Wireless Receiver will automatically switch to standby mode. In power saving mode, both LEDs will turn red. LEDs will turn blue when there is any audio signal back. If you operate main unit then wireless speakers (rear speakers) sound within a few seconds in standby mode. 14 Setting up Be careful of the following • Be careful to make sure children do not put their hands or any objects into the *speaker duct. *Speaker duct: A holl for plentiful bass sound on speaker cabinet(enclosure). • Set the distance between this unit and Wireless Receiver within 10m. • Optimum performance can be implemented only when the Wireless Transmitter and the Wireless Receiver within distance of 2m to 10m is used since communication failure may occur if longer distance is used. • Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are reversed, the sound will be distorted and will lack bass. • It takes a few seconds (and may take longer) for the Wireless Transmitter and Wireless Receiver to communicate with each other. • Use the rear speaker at least 30 CM away from either TV screen or PC monitor About Ferrite Core (for EMI only) Be sure to attach the ferrite core to the speaker cable (for connecting to this unit and wireless receiver). This ferrite core can reduce noises. How to attach the ferrite core 1 Press the stopper [a] of the ferrite core to open. 2 Wind the speaker cables once on the ferrite core. (Refer to the fig.3 and comment.). 3 Close the ferrite core until it clicks. The length here is as short as possible. (fig.3) Rear of wireless receiver 15 16 Connections to Your TV Make one of the following connections, depending on the capabilities of your existing equipment. Tips: • Depending on your TV and other equipment you wish to connect, there are various ways you could connect the player. Use only one of the connections described below. • Please refer to the manuals of your TV or other devices as necessary to make the best connections. Cautions: • Make sure the player is connected directly to the TV. Tune the TV to the correct video input channel. • Do not connect your player via your VCR. The image could be distorted by the copy protection system. HDMI Connection If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable. Connect the HDMI OUT jack on the player to the HDMI IN jack on a HDMI compatible TV or monitor (H). Set the TV’s source to HDMI (refer to TV’s Owner’s manual). Notes: • You must select a HDMI audio output that your TV accepts using [HDMI Audio] options on the [Setup] menu (see page 26). • If a connected HDMI device does not accept the audio output of the unit, the HDMI device’s audio sound may be distorted or may not output. Tips: • You can fully enjoy digital audio and video signals together with this HDMI connection. • When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution Setting” on page 18-19.) • Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Setup] menu (see page 24). Cautions: • Changing the resolution when the connection has already been established may result in malfunct...
Эта инструкция также подходит к моделям:Домашние кинотеатры - HB954TBW (4.67 mb)