Оценок - 3, средний балл: 3.3
(
)
)
|
К этому устройству также есть другие инструкции:
Домашние кинотеатры - HTR-210SS (2.25 mb)
Домашние кинотеатры - HTR-210SS (2.48 mb)
Фрагмент инструкции
Colour tube + – FRONT R – + – + FRONT L – + SURR R + – + – SURR L + – E e AE e AEe AEe AEe ASUBWOOFER CENTER Front speaker (Right) Front speaker (Left) Subwoofer Surround speaker (Right) Surround speaker (Left) Center speaker Note (Except for HTD-710SF) Before you connect the speakers, attach the colour labels onto the speakers so that you can identify the speakers to be connected. 12GB Tips • Since the subwoofer does not emit highly directional signals, you can place it wherever you want. • (Except for HTD-710SF) For greater flexibility in the positioning of the speakers, use the optional | WS-FV11 or WS-FV10D floor stand (available only in certain countries). Attaching foot pads (Except for HTD-710SF) To prevent speaker vibration or movement, attach the supplied foot pads to the speaker as shown in the illustration below. Note Be sure to attach the supplied foot pads to the subwoofer as well. Installing the speakers on the wall You can install your front and surround speakers on the wall. 1 Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. See the illustrations below. more than 4 mm more than 25 mm 4.6 mm 10 mm 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm. Getting 5 to 7 mm 3 Hang the speakers on the screws. 4.6 mm 10 mm Hole on the back of the speaker Notes • Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied. • Contact a screw shop or installer regarding the wall material or screws to be used. • Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc. Hole on the back of the speaker continued 13GB To change the speaker cord If you want to change the speaker cord, you can detach the supplied speaker cord from the connector. 1 Press the connector onto a flat surface. Make sure that the catcher is facing the flat surface. catcher 2 Pull the speaker cord from the connector. 3 Twist the stripped ends of the speaker cord you want about 10 mm and insert the speaker cord into the connector. Make sure that the speaker cord is inserted according to its polarity : + to + and – to –. Otherwise the sound will be distorted and will lack bass. + – (+) (–) 4 Remove the connector from the flat surface. Note To avoid the speaker cord from coming off the speaker connector – do not use a smaller-size speaker cord. We recommend that you use the AWG#18 to AWG#24 speaker cords. – use the same speaker cord size for all the speaker connectors. – twist the stripped ends of the speaker cords. – insert the speaker cord completely into the speaker connector. 4: Connecting the AC power cord Connecting the AC power cord Connect the AC power cord to a wall outlet. To a wall outlet AC power cord Performing initial setup operations Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults. Use the buttons on the receiver for the operation. 1 Press ?/1 to turn off the receiver. 2 Hold down ?/1 for 5 seconds. “INITIAL” appears in the display. The following are reset to their factory settings. • All settings in the SET UP, LEVEL and TONE menus. • The sound field memorized for each input and preset station. • All sound field parameters. • All preset stations. • MASTER VOLUME is set to “VOL MIN”. 14GB 5: Setting up the speakers You can use the SET UP menu to set the distance and location of the speakers connected to this receiver. 1 Press ?/1 to turn on the receiver. 2 Press MAIN MENU repeatedly to select “ SET UP ”. 3 Press or repeatedly to select the parameter you want to adjust. For details, see “Speaker setup parameters” below. 4 Press or repeatedly to select the setting you want. The setting is entered automatically. 5 Repeat steps 3 and 4 until you have set all of the items that follow. Speaker setup parameters The initial setting is underlined. x L R DIST. X.X m (Front speaker distance) Initial setting: 3.0 m Lets you set the distance from your listening position to the front speakers (A). You can adjust from 1.0 meter to 7.0 meters in 0.1 meter steps. If both front speakers are not placed an equal distance from your listening position, set the distance to the closest speaker. 30°30° 100°-120°100°-120° ACCAB x C DIST. X.X m (Center speaker distance) Initial setting: 3.0 m Lets you set the distance from your listening position to the center speaker. Center speaker distance should be set from a distance equal to the front speaker distance (A) to a distance 1.5 meters closer to your listening position (B). x SL SR DIST. X.X m (Surround speaker distance) Initial setting: 3.0 m Lets you set the distance from your listening positio...
Эта инструкция также подходит к моделям:Домашние кинотеатры - HTD-710SF (1.22 mb)
Домашние кинотеатры - HTD-710SS (1.22 mb)
Домашние кинотеатры - HTP-32SS (1.22 mb)
Домашние кинотеатры - HTR-110SS (1.22 mb)