Оценок - 2, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Домашние кинотеатры - DAV-DZ260 (3.98 mb)
Домашние кинотеатры - DAV-DZ260 (1.35 mb)
Фрагмент инструкции
. • When you change the [CONNECTION] setting in [SPEAKER SETUP] (page 51), the [SPEAKER FORMATION] setting returns to [STANDARD]. Other Operations SPEAKER FORMATION STANDARD 7 Press C/c to select a setting. • [STANDARD]: Select this when you install all the speakers normally. 71GB Calibrating the Appropriate Settings Automatically [AUTO CALIBRATION] D. C. A. C. (Digital Cinema Auto Calibration) can set the appropriate surround sound automatically. Note • The system outputs a loud test sound when [AUTO CALIBRATION] starts. You cannot turn the volume down. Give consideration to children and neighbors. • Make sure that the headphones are not connected to the unit. You cannot operate the following Steps with the headphones connected. 1 Press FUNCTION +/– repeatedly until “DVD” appears in the front panel display. 2 Press DISPLAY while the system is in stop mode. The Control Menu display appears on the TV screen. 3 Press X/x to select [SETUP], then press . The options for [SETUP] appear. 4 Press X/x to select [CUSTOM], then press . The Setup Display appears. 5 Press X/x to select [AUDIO SETUP], then press . The options for [AUDIO SETUP] appear. 6 Press X/x to select [AUTO CALIBRATION], then press . The options for [AUTO CALIBRATION] appear. 7 Connect the calibration mic (supplied) to the A.CAL MIC jack on the front panel Set up the calibration mic at the ear level using a tripod, etc. (not supplied). The front of each speaker should face the calibration mic, and there should be no obstruction between the speakers and the calibration mic. AUDIO IN / A.CAL MIC Ca lib r a tio n m i c 8 Press C/c to select [YES]. 9 Press . [AUTO CALIBRATION] starts. Be quiet during the measurement. Note • Avoid being in the measurement area and making noise during the measurement (about 3 minute), to avoid measurement failure. During the measurement, test signals are output from the speakers. • The environment of the room in which the system is installed may affect measurements. • If an error message appears, follow the message, then select [YES]. An error message appears when: – the headphones are connected to the unit. – the calibration mic is not connected. – front speakers are not correctly connected. – surround speakers are not correctly connected. 72GB – front and surround speakers are not correctly connected. 10 Press C/c to select [YES] or [NO], then press . x The measurement is OK. Disconnect the calibration mic, then select [YES]. The result is implemented. x The measurement is not OK. Follow the message, then select [YES] to retry. Note • While the Auto Calibration function works: – do not turn off the power. – do not press any button. – do not change the volume. – do not change the function. – do not change the disc. – do not insert or eject a disc. – do not connect the headphones to the unit. – do not disconnect the calibration mic. • The measurement for [SUBWOOFER] is always [YES] since the system does not perform subwoofer calibration. Tip • You can check the distance between the listening position and each speaker. See page 51. Controlling the TV with the Supplied Remote You can control the TV (Sony only) by using following buttons. Use these buttons (other than TV [/1, THEATRE, TV INPUT, and TV VOL +/–) while pressing the TV button. Note • Depending on the TV, you may not be able to control your TV or to use some of the buttons. By pressing You can TV [/1 Turn the TV on/off. THEATRE Enjoy optimal image suited for movies. TV INPUT Switch the TV’s input source between the TV and other input sources. TV VOL +/– Adjust the TV volume. PROG +/–* Select the TV channel. Number Select the TV channel. buttons*, -* ENTER* TOOLS* Displays the operation menu for the current display. RETURN* Return to the previous channel or layer on the menu of the TV. MENU* Display the menu of the TV. MUTING* Turn off the TV sound temporarily. C/X/x/c*, * Select the item on the menu. * Use these buttons while pressing the TV button. Other Operations 73GB Using the Sound Effect Reinforcing bass frequencies You can reinforce bass frequencies. Press DYNAMIC BASS. “D. BASS ON” appears in the front panel display and bass frequencies are effectively reinforced. To turn off the sound effect Press DYNAMIC BASS again. Enjoying the sound at low volume You can enjoy sound effects or dialogue, as you would in a movie theater, even at low volume. It is useful for watching movies at night. Press NIGHT. “NIGHT ON” appears in the front panel display and the sound effect is activated. Note • This effect does not work for a Super Audio CD. When you load a Super Audio CD during “NIGHT ON,” the sound effect turns off automatically. • When sound is output from the center speaker, this effect is more pronounced, as speech (movie dialog, etc.) is easy to hear. When sound is not output from the center speaker, or you are using the headphones, the system optimally adjusts the volume. To turn off the sound effect Press NIGHT again. Using the Sleep Timer You can set the s...