Оценок - 5, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Домашние кинотеатры - HT-DDW870 (113.52 kb)
Домашние кинотеатры - HT-DDW870 (2.05 mb)
Домашние кинотеатры - HT-DDW870 (4.49 mb)
Фрагмент инструкции
VIDEO 1 VIDEO IN AUDIO IN AUDIO OUT VIDEO IN VIDEO OUT VIDEO 2 AUDIO IN SA-CD/ CD IN DVD IN COAXIAL MD/TAPE SA-CD/CD L R L R OUT ININ VIDEO IN DVD AM AUDIO IN AUDIO OUT VIDEO OUT L R L R DIGITAL ANTENNA OPTICAL VIDEO 2 IN MONITOR SUB WOOFER AM loop antenna (supplied) FM wire antenna (supplied) * * The shape of the connector varies depending on the area code. Notes • To prevent noise pickup, keep the AM loop antenna away from the receiver and other components. • Be sure to fully extend the FM wire antenna. • After connecting the FM wire antenna, keep it as horizontal as possible. 12GB 3: Connecting speakers Connect your speakers to the receiver. This receiver allows you to use a 6.1 channel speaker system. To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a center speaker, and two surround speakers) and a sub woofer (5.1 channel). You can enjoy high fidelity reproduction of DVD software recorded in the Surround EX format if you connect one additional surround back speaker (6.1 channel) (see “Selecting the surround back decoding mode” on page 33). Example of 6.1 channel speaker system configuration Front speaker (right) Surround speaker (right) Center speaker Front speaker (left) Sub woofer Surround speaker (left) Surround back speaker Tips • When you connect 6.1 channel speaker system, place the surround back speaker behind the listening position (page 19). • Since the sub woofer does not emit highly directional signals, you can place it wherever you want. • For greater flexibility in the positioning of the speakers, use the optional WS-FV11 or WS-FV10D floor stand (available only in certain countries). • You can also install the front, surround and surround back speakers on the wall (see page 16). Note Connect the long speaker connecting cords to the surround and surround back speaker terminals and the short speaker connecting cords to the front and center speaker terminals. Getting Started continued 13GB Attaching foot pads To prevent speaker vibration or movement, attach the supplied foot pads to the speaker as shown in the illustration below. Note Be sure to attach the supplied foot pads to the sub woofer as well. 14GB Required cords A Speaker cords (supplied) B Monaural audio cord (supplied) (+) Black (–) AUDIO OUT FRONT A CENTER FRONT B LR LR LR + +–– – SPEAKERS SUB WOOFER AEeAEeAEeEeAINPUT BEeASPEAKERS FRONT B* EeASPEAKERS SURROUND LR SURROUND BACK + Sub woofer Center speaker Surround back speaker Front speaker (left) Front speaker (right) Surround speaker (right) Surround speaker (left) * If you have an additional front speaker system, connect them to the SPEAKERS FRONT B terminals. You can select the front speakers you want to use with the SPEAKERS (OFF/A/B/A+B) button. For details, see “Selecting the speaker system” (page 40). Getting Started continued 15GB Installing the speakers on the wall You can install your front, surround and surround back speakers on the wall. 1 Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. See the illustrations below. more than 4 mm (5/32 inch) more than 25 mm (1 inch) 4.6 mm (3/16 inch) 10 mm (13/32 inch) Hole on the back of the speaker 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm (7/32 to 9/32 inch). 3 Hang the speakers on the screws. Hole on the back of the speaker 4.6 mm (3/16 inch) 10 mm (13/32 inch) Notes • Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied. • Contact a screw shop or installer regarding the wall material or screws to be used. • Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc. 5 to 7 mm (7/32 to 9/32 inch) 16GB 4: Connecting the AC power cord Setting the voltage selector for the receiver and sub woofer If your receiver and sub woofer has a voltage selector on the rear panel, check that the voltage selector is set to the local power supply voltage. If not, use a screwdriver to set the selector to the correct position before connecting the AC power cord to a wall outlet. Receiver VOLTAGE SELECTOR 120V 220V 240V Connecting the AC power cord Connect the AC power cord to a wall outlet. FRONT B LR LR b To a wall outlet AC power cord Getting Started Sub woofer 120V 240V 220V continued 17GB Performing initial setup operations Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults. Use the buttons on the receiver for the operation. 1 Press ?/1 to turn off the receiver. 2 Hold down ?/1 for 5 seconds. “PUSH” and “ENTER” appears in the display alternatingly. 3 Press ENTER. “CLEARING” appea...