Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
indicator lights up in standby mode and goes out when the [INPUT SELECTOR, <, >] unit is turned on. For selecting input. [8, POWER] [VOLUME] Press to switch the unit from on to standby mode or vice Volume control. versa. In standby mode, the unit is still consuming a small [ ] Headphone jack amount of power. Plug type: O3.5 mm (1/8") stereo [-MENU, .SETUP, RETURN] • Sound does not come from the speakers if you connect • For entering menus and setup to make various settings. headphones. • For returning to previous menus. • Avoid listening for prolonged periods of time to prevent [TUNE, 2 / 3, 1 / 4] hearing damage. For tuning the radio and selecting menu or setup items. 9 10 [SETUP MIC] jack [ENTER] For calibration microphone. Used during menu or setup operations. Remote control signal sensor 1 2 3 4 Display [TUNED, ST, MONO]1 6 [ % DIGITAL, DTS, % PL..] 1 2 3 4 5 6 7 9 8 10 TUNED MONO SLEEP PCMST ft M C.FOCUS W 2 3 4 5 Radio indicators Lights to indicate the source's input signal and decoding TUNED: A station is tuned format used. ST: A stereo FM broadcast is tuned % DIGITAL: Dolby Digital sources DTS: DTS sources MONO: You have switched to monaural mode to improve % PL..: Dolby Pro Logic .. decoder is being used reception 7 [SFC, 2CH MIX] [SLEEP] SFC: Appears when you are using an SFC modeSleep timer indicator. 2CH MIX: Appears when you are listening to a multi-channel General display source with headphones Shows the input mode, radio frequency and other general [M] Flashes or lights during presetting. information. [ft, kHz, MHz] PCM: Lights when the PCMFIX mode is set 89 Distance and frequency unit indicators ft: feet (speaker distance) [PCM, C.FOCUS] C.FOCUS: Appears when you are using Center Focus kHz: AM, or PCM sampling frequency [DIGITAL INPUT] MHz: FM Lights when input is digital. 10 [W] Lights when you are using the digital transmitter (. page 7). Flashes when there is no link between the main unit and the wireless system (For details, refer to the operating instructions for SH-FX67). 5 6 RQTX0175 Speaker setup STEP 1 3 3 3 3 SURROUND Lch Lch Lch SURROUND Lch SURROUND SURROUND 4 4 4 4 SURROUND Rch Rch Rch SURROUND Rch SURROUND SURROUND 6 6 WOOFER SUB SUB WOOFER 6 6 WOOFER SUB SUB WOOFER 1 1 1 1 Lch Lch Lch FRONT FRONT FRONT 5 5 CENTER CENTER 5 5 CENTER CENTER Lch FRONT 2 2 2 2 Rch Rch Rch FRONT FRONT FRONT Rch FRONT Speaker setup Supplied accessories Place the front, center, and surround speakers at approximately the same distance from the seating position. Auto Speaker Setup compensates for any differences (. pages 11 to 12). The angles in the diagram are approximate. Placement of speakers. Keep your speakers at least 10 mm (13/32") away from the system for proper ventilation. Note Positioning for best effect How you set up your speakers can affect the bass and the sound field. Note the following points. Place speakers on flat secure bases. Placing speakers too close to floors, walls, and corners can result in excessive bass. Cover walls and windows with a thick curtain. • • Front speakers (left, right) Place on the left and right of the TV at seated ear height so that there is good coherency between the picture and sound. Center speaker Place underneath or above the center of the TV. Aim the speaker at the seating area. Surround speakers (left, right) Place on the side of or slightly behind the seating area, higher than ear level. Subwoofer The subwoofer can be placed in any position as long as it is at a reasonable distance from the TV. Note that some experimentation can yield the smoothest low frequency performance. Placement near a corner can increase the apparent output level, but can result in unnatural bass. Center speaker Front speaker (L) Front speaker (R) Subwoofer Surround speaker (L) Surround speaker (R) Speaker cables (3 short, 2 long) 1 Speaker sticker sheet Placement of speakers SUB WOOFER 6 Lch SURROUND Lch SURROUND 3 3 SUBWOOFER CENTER +: White .: White (Blue line) FRONT (R) FRONT (L) SURROUND (L) SURROUND (R) Push! Insert the wire fully. Attach the speaker-cable stickers to make connection easier. Speaker-cable sticker Do not insert the wires beyond the wire insulation. Be careful not to cross (short-circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers. Connect the speakers to the receiver • Turn off all components before making any connections. • Peripheral equipment and cables sold separately unless otherwise indicated. • To connect equipment, refer to the appropriate operating instructions. Other speaker setup options Plate thickness plus ¦ Fitting optional speaker stands Example: Surround speaker 7.0 mm (9/32") to (For front, center and surround speakers) Metal screw 10 mm (13/32") Ensure the stands meet these conditions before purchasing them. hole Note the diameter and length of the screws and the distance between For attaching screws as shown in the diagram. to speaker stands. Speaker stand • The stands must be able to support over 10 k...