Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
.use different types at the same time. .heat or expose to flame. .take apart or short circuit. .attempt to recharge alkaline or manganese batteries. .use batteries if the covering has been peeled off. Mishandling of batteries can cause electrolyte leakage which can damage items the fluid contacts and may cause a fire. Remove if the remote control is not going to be used for a long period of time. Store in a cool, dark place. .Use Aim at the sensor (l14), avoiding obstacles at a maximum range of 7 m (23 feet) directly in front of the unit. STEP7 Plug-in Auto Tuning After plugging the unit into your household AC outlet and pressing [I] to turn the unit on for the first time, the unit automatically tunes in all the channels it can receive and sets the clock. The unit determines the type of transmission, TV or CATV, as follows: TV: when there are less than 5 CATV channels. CATV: when there are 5 or more CATV channels. Preparation .Confirm that the antenna is connected correctly. .Turn on the television and select the video input for the VHS. .Press [VHS] to put the remote control in VHS mode. Press [I] to turn on the unit. Plug-in Auto Tuning starts and the unit puts the stations it can receive into channels (l37, Channel range). AUTO CHANNEL SET PROCEEDING END :MENU 2 The unit starts auto clock setting when finished, then displays the time. [Note] If auto tuning stops partway (by changing the source, turning the unit off, or due to a power failure). 1 Disconnect the AC power supply cord on the main unit and then reconnect it. 2 Turn on the main unit. To cancel partway Press [MENU]. .To start Plug-in Auto Tuning again (after relocation, for example) Preparation .Press [I] to turn on the unit. .Make sure there is no video cassette tape loaded in the unit. .Press [DVD/VHS] to select “VHS” as the source. 1 Press and hold [W CH] and [X CH] on the main unit simultaneously for 3 seconds until the channel changes to “2”. 2 3 Disconnect the AC power supply cord on the main unit and then reconnect it. Turn on the main unit. Plug-in Auto Tuning restarts. Disappears 2 Antenna system and channel captions all revert to the default values when you perform the procedure above. Reset the timer recording settings. (If necessary reset the clock first. l36, CLOCK SET) .To set the channels manually (l37). .If the unit couldn’t set the clock automatically The MANUAL CLOCK SET screen appears. Set the time manually (l36). 11 RQT7921 12 RQT7921 12 RQT7921 VOLUME 1 2 3 4 5 6 7 8 0DISC 9 CH NAVI CANCEL SPEEDPROG SKIP SLOW/SEARCH TOP MENU MENU ENTER DIRECT PLAY NAVIGATOR RETURN STATUS/ FUNCTIONS LIST TV INPUT SELECTOR FM/AMDVD/VHS DVD TVVHS TUNER PICTURE MODE SETUP OPEN/CLOSE/EJECT JET REW ENTER TV VOLTV VOL MULTI RE-MASTER MIX 2CH PROGRESSIVE REPEAT QUICK OSD ZOOM CD MODE PLAY MODE H.BASS C.FOCUS TEST CH SELECT SUBWOOFER LEVEL SFC SUPER SRND MUTING CM SKIP DISC REVIEW REPLAY REC ADVANCE QUICK SLEEPRESET SHIFTSHIFT PL AUDIO TV/VIDEO S10 DVD/VHS TV STEP8, 2 TV DVD CH CH STEP8, 2 Numbered buttons SETUP ENTER RETURN TV VOL TV VOL SHIFT TV/VIDEO STEP8 TV manufacturer setting You can control the television by entering the remote control code. 1 Refer the following chart for the code for your television. Manufacturer Code No. Manufacturer Code No. Panasonic 01, 02 PHILIPS 06 FISHER 14 PIONEER 02, 10, 19 G.E. 02, 03, 07, 09 QUASAR 02 GOLD STAR 07, 15 RCA 03, 07, 09, 13, 23, 24, 25 HITACHI 05, 07 SANYO 14 JVC 12 SHARP 08, 21 LXI 03, 06, 07, 10, 14, 15 SONY 04 MAGNAVOX 06, 07, 11, 15, 22 SYLVANIA 06, 07, 15 MITSUBISHI 07, 15, 16, 21 SYMPHONIC 17 NEC 07, 15 TOSHIBA 10, 21 PHILCO 06, 07 ZENITH 18, 20 2 Aiming the remote control at the television While pressing and holding [TV], press the numbered buttons to enter the code number. .Example: To select 01, press [0] l[1]. .The remote control outputs the on/off signal. If the code is correct, the equipment turns on or off. If it doesn’t, try entering another code. [Note] .If your television brand is not listed or if the code listed for your television does not allow control of your television, this remote control is not compatible with your television. .Re-enter the codes after you change the batteries. .TV operation Switch the remote control mode to TV. Press [TV] before doing TV operations. When in TV mode, the [TV] button lights each time you press an operation button. Operation Buttons Remote control TV mode [TV] Power on/ standby [ITV] TV/Video switch [TV/VIDEO] Selecting channels [WCH], [XCH] or numbered buttons [1–9, 0, S10/ENTER]. .[S10/ENTER] is used to confirm channel selection on some televisions manufactured by other companies. Adjusting volume [TV VOLj] [TV VOLi] STEP9 DVD QUICK SETUP Turn on the television and select the video input for the DVD. The QUICK SETUP screen assists you to make necessary settings such as: .Menu Language (l27) .TV Type (l26) .TV Aspect (l26) 1 Press [DVD] to put the remote control in DVD mode. 2 Press [I] to turn on the unit. 3 Press [DVD/VHS] to select “DVD/CD” ...