Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Incorrect dip switch settings may cause the interface not to work properly or not to operate at all. Disconnect the vehicle harness from module and cycle ignition off for 5 seconds after changing the switches! After making changes to the frequency selector be sure to tune to the correct FM frequency on which the iPod will be heard. Step 2: Install the DPR-RDS1 in the vehicle 1. Pull vehicle into the service bay. 2. Make sure that the radio code is available before disconnecting the battery. Disconnect both battery terminals. These cables must be disconnected during installation for proper initialization of the module when its connected. 3. Pull out the radio by removing surrounding trims and screws to access the factory antenna connector. Most trims can be removed by carefully pulling on the piece or using trim removal tools. trim is usually held in place by snap-in clips. Consult your dealership if additional information is needed on removing the radio. NOTE: Try to select a transmitting frequency that is not Interface Unit “frequency selector” Intruction d’installation Phase 1: Ajustez le choix de frequence Les commutateurs sont situes sur l'unite et sont utilises pour placer la meilleure frequence pour l'emission. Les arrangements incorrects peuvent faire ne pas fonctionner correctement ou ne pas fonctionner l'unite du tout. Deconnectez le cable d'alimentation pendant 5 secondes apres changement les positions de commutateur. Apres avoir apporte des modifications, accordez a la radiofrequence sur votre radio pour entendre l'iPod Phase 2: Installez le DPR-RDS1 pour vehicule 1) S’arreter le vehicule en le aire de reparation 2) Notez le code radio avant de commencer. Deconnectez les bornes de batterie pour s'assurer l'unite initialise correctement. 3) Enlevez les panneaux de vehicule pour acceder au connecteur de radio et d'antenne. Enlevez les panneaux en tirant doucement et a l'aide des outils appropries pour ne pas les endommager. Consultez votre agence si les informations supplementaires ou l'aide sont necessaire. Step 3: Install the DPR-RDS1 in the vehicle (continued) 4. You can access the factory antenna port located on the back of the radio. If the factory antenna cable is connected, unplug it and plug the universal antenna connector into the receptacle. Connect +12 volt, ground and remote wire leads to their proper sources. 5. Connect the power/antenna cable and the iPod docking cable to the interface unit. Apply cable ties to secure the cables. 6. Verify that all connections have been properly made. 7. Reconnect the car’s battery. Test the unit before seating the cables and reinstalling the panels/trim. universal antenna Phase 2: Installez le DPR-RDS1 pour vehicule(suite …) 4) Vous pouvez acceder au connecteur d'antenne derriere la radio. Debranchez l'antenne et branchez le connecteur universel d'antenne dans la radio. Reliez le 12V+, BATT et de REM a leurs raccordements corrects 5) Connectez le cable d'antenne /puissance et le cable d' iPod a l'unite et fixez l'unite avec des serres-cable 6) Inspectez que les raccordements sont corrects 7) Connectez la batterie. Test the function of unit before finish the installation of the panels Using the DPR-RDS1 Select the FM radio source on the radio and tune to the frequency that was selected on the interface unit. As soon as the radio is tuned to the appropriate frequency, audio from the iPod will be heard. About RDS Radios with RDS capability allow the currently playing song title and album name to be displayed on the screen of the radio. To find out if a radio has RDS, tune to a popular radio station and if the station name is displayed then the radio has RDS capability. iPod and iPhone charging The iPod or iPhone will charge whenever the vehicle’s ignition is on Problem Solution Cannot hear audio from iPod. Make sure to select the FM source on the radio and tune to the correct FM frequency. Check DIP switch settings. With the ignition OFF disconnect vehicle harness from module for a few seconds and reconnect. Audio from iPod receives high amounts of static and radio interference. Select an FM frequency that is not already occupied by a radio station. Select a frequency preset with the least amount of static. It’s best to drive around and experiment to find the ideal setting. If problem persists, professional installation is recommended. Utilisant le RDS1 Choisissez la source de FM sur la radio et veuillez changer de frequence a la station de prereglage que vous avez choisie sur l'unite. L'acoustique sera entendue du systeme audio. RDS Les radios capables du RDS montrent l'information de station de radio sur l'ecran de la radio. Pour verifier les possibilites de la radio, choisissez une station de radio populaire et voyez si l'information est affichee sur l'ecran Chargement de iPod et iPhone Votre iPod ou iPhone chargera quand votre ingition de vehicule est allume Problem Solution Ne peut pas entendre l’acoustique d’iPod Confirmez la source de la radio es...