Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Please note: This appliance is designed solely to produce ice cubes and dispense water. Other types of use are not permitted and may prove dangerous. The CDA Group Ltd will not be held liable for any damage caused by incorrect use of the appliance •Read all instructions thoroughly before use. •Before first use, you must allow the icemaker to settle for at least twenty four hours prior to switching the power on. •To protect against fire, electrical shock and injury to persons do not immerse cord or plugs in water or other liquid. •The use of accessory attachments not recommended by The CDA Group Ltd may result in fire, electric shock or injury. •If the appliance is switched off, you should allow five minutes before switching it on again to prevent unnecessary damage to the compressor. •You should only use cold drinking water in this appliance, with water hardness level less than 7.F. 1 Icemaker Display Control Panel Water Nozzle Ice Drawer Ice Water Tray Drip Tray Icemaker control panel ON OFF 1 2 3 4 5 6 1. On button 2. Off button 3. Water glass button – this button dispenses a small amount of water. 4. Water jug button – this button dispenses a large amount of water. 5. Manual water button – this button dispenses water as long as the button is pressed. 6. Settings button – this button changes the preset amounts of water. The Icemaker Before first use: 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Turn on the machine at the power switch on the left side of the machine The machine will automatically start a drain cycle, which will take approximately five minutes. During this process, the display will show ICE OFF WATER EMPTY. 3. Push the machine back into the housing. 4. Switch on the machine by pressing the button. 5 The machine is now ready for use and the display shows ICE ON WATER READY. Please note You should clean the pipes through before first use to remove any impurities in the system after installation. To do so, place a jug under the water nozzle and press for approximately two minutes, disposing of the water dispensed. The Icemaker To make ice The icemaker will make ice automatically once it is switched on and will continue to make ice until the ice compartment is full. Whenever ice is removed, the icemaker will make more ice until the compartment is full again. To dispense water The amount of water dispensed from the water nozzle is controlled by three different buttons. – water glass – water jug – manual setting – this button dispenses water as long as the button is pressed. To change the preset buttons It is possible to adjust the amount of water dispensed by the preset buttons ( & ). To do so, place a glass or jug under the water nozzle and press until the required amount has been dispensed. Then confirm the setting by pressing buttons & for the water glass button or buttons & for the water jug button. Please note: To stop water dispensing once a preset button has been pressed, simply press the button again. The ice water tray is located below the ice drawer. In normal use this fills with water, this does not constitute a fault. This water is used in the ice making process and is replaced every 24 hours by the automatic drain cycle. You should use the water from the water nozzle for drinking. The water nozzle is height adjustable for ease of use. To adjust the height, hold the black outer section of the water nozzle and raise or lower it to the height required. The nozzle will automatically remain at the height set. To dispense ice When the ice drawer is full, the display shows ICE FULL WATER READY. Open the drawer fully and use the scoop provided to remove the ice as required. Please note: If the ice drawer is not emptied for a long period of time, the appliance will go on standby for approximately ten minutes, and the display shows ICE OFF WATER READY. After the standby period has ended, the appliance will begin to make ice again. If you do not want to wait for the standby period to finish, press the button. If the ice drawer is not emptied regularly an excessive accumulation of ice cubes could hinder the movement of the upper carriage. You are recommended to open the ice drawer slowly after a long period of time on standby and regularly remove ice cubes from the drawer. Care and maintenance Always disconnect the appliance from the power before any cleaning or maintenance. As the icemaker has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Proprietary stainless steel cleaners are available. We recommend the CDA E-Cloth available from the CDA Sales Team for cleaning stainless steel surfaces. You should remove and clean regularly the ice compartment drawer an...