Оценок - , средний балл:
(
)
)
Производитель: Ice-O-Matic
Размер: 782.4 kb
Название файла: b2eafeb5-f771-4d9a-8b79-9b9383c0ffe2.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
The CD10022, CD10522, CD20030 and CD20530 are Ice-O-Matics brand hotel/motel ice dispenser. The CD10022 is designed to use a Ice-O-Matic model GC300, 550, ECP 400, 550, 556 ice machine as the source for ice. The CD-200-30 is designed to use a Ice-O-Matic model ICE 250, 400, 500 and 600 ice machine as the source of ice. Ice from the cuber falls into the insulated hopper, where it is stored until needed. When a user pushes the dispense button, a rotating wheel scoops the ice up and moves the ice to the top of the hopper where there is an outlet to the ice chute. Table of Contents Specifications/Limitaions . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3 - 4 Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5 - 10 Final Check List/Initial Start Up/Electrical Sequence . . . . . . . . . . . . . . Page 11 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13 - 14 Service Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15 Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . .Page 16 Electrical Schematics . . . . . . . . . . . . . . . . . . . . . . . .Page 17 - 19 NOTE: The warning symbol where it appears in this manual. It is an alert for important safety information on a hazard that might cause serious injury. NOTE: Keep this manual for future reference. 1 CD10022 CD20030 CD10522 CD20530 Specifications Limitations: • Must meet the same limitations as the cuber installed on top of it: • 50o F air minimum • 100o F air maximum • Must be installed indoors • Must allow space to the right for air intake when using air cooled machine. • The CD10022 and CD10522 are compatible only with Ice-O-Matics’ models GC 300, 550, ECP 400, 550, 556. • The CD20030 and CD20530 are compatible only with Ice-O-Matics’ models ICE 250, 305, 400, 500, 600. • Must allow space for utility connections at the back. • Must have a drain. Model Dimensions (with legs) Basic Electrical Finish Ice StorageCapacity (ARI) MaxFuse Size Min Circuit Ampacity CD10022 22”x30”x50” 115/60/1 S. STEEL 90 lbs. 15 2.5 CD10522 22”x30”x50” 230/50/1 S. STEEL 90 lbs. 15 1.3 CD20030 30”x30”x53” 115/60/1 S. STEEL 140 lbs. 15 1.9 CD20530 30”x30”x53” 230/50/1 S. STEEL 140 lbs. 15 1.0 2 CD10022 CD10522 Installation: General CD20030 CD20530 After the carton has been removed from the dispenser, the legs may be installed. Place flat portions of the carton on the floor behind the dispenser and lay the dispenser down on its back. Thread the legs into the base of the dispenser. Be sure that the legs are screwed in all the way. Turn the leg levelers in all the way. Move the dispenser to an upright postion and set it in the location where it will be installed. Note where the drain lines and electrical connections will be made. Drain: The dispenser has a 3/4” FPT drain fitting at the bottom center of the back panel. Connect 3/4” rigid tubing to this connection, a vent is recommended for most installations. Route the drain tubing to the building drain. Follow all applicable plumbing codes. Because the tubing will be very cold, insulation is recommended. Electrical: There is an electrical junction box on the lower back panel. Make the electrical connections there. Follow all applicable electrical codes. Use a licensed electrician. The dispenser must be installed so that it is a separate piece of equipment from the ice machine. The drains and electrical supply must be separate. 3 NOTE Remove any packaging material from inside the storage bin. Retain keys for later use. Check that gasket tape is on the top outside edge of the dispenser where the ice machine will rest. CD10022 CD20030 CD10522 CD20530 Installation: Ice Machine Check that gasket tape has been placed at the outside edge of the dispenser top. Place corner posts from the carton on top of the dispenser, at the left and right corners. Place the ice machine onto the dispenser. The ice machine is heavy, use of a mechanical hoist is recommended. Carefully remove cardboard supports and allow ice machine to rest on dispenser gasket. Follow all instructions for installation of the ice machine. 4 CD10022 CD20030 CD10522 CD20530 Kits: Coin Mechanism Kits are available to install a coin mechanism, a room key mechanism or a key card mechanism. All kits come with detailed instructions which are also listed below. Please follow these instructions carefully to complete the addition of the coin mechanism kit to the CD10022, CD10522, CD20030, and CD20530 ice dispenser. 1. Disconnect the dispenser from its electrical power supply (failure to do so may result in a serious injury). Electrical shock hazard. Electrical shock can cause personal injury. Disconnect power before begining to service components. 2. Unlock and remove the decorative front cover, then remove the top front brace and the control box cover. 3. Remove all wires from the push button switch. Now remove the nuts that secu...