Войти:
Сортировка : Названию ↑   Загрузкам   Оценке   Размеру ↑  
Скачали: 11   Размер: 3 mb   Производитель: Campbell Hausfeld  
Категория: Диктофоны
@name@name@name

Voltage drop in the extension cord may significantly degrade performance of the welder. Welding accessories for the welder are inside wire feed compartment. 1. Place handle assembly on welder, aligning two holes in plastic ends with threaded holes in welder housing (Fig. 2). 2. Insert screws through cord wraps and handle ends and fasten into cabinet. 3. Attach cylinder base to unit as shown (Fig. 3). 1. Loosen hex bolt/nut on work clamp. 2. Insert cord (labeled ‘work clamp’ on the front panel of

Скачали: 10   Размер: 1 mb   Производитель: Campbell Hausfeld  
Категория: Диктофоны
@name@name@name

Extremely toxic fumes are created when these metals are heated. 4. Connect the work clamp to the work piece or workbench (if metal). Make sure the contact is secure. Avoid surfaces with paint, varnish, corrosion, or non-metallic materials. 5. Position the Heat Selector on the front panel to the desired setting. See application decal inside door of wire feed compartment for proper heat settings. NOTE: These settings are general guidelines only. Heat setting may vary according to welding con

Скачали: 106   Размер: 3 mb   Производитель: Campbell Hausfeld  
Категория: Диктофоны
@name@name@name

Wire jammed 2. Out of wire 3. Not enough tension 4. Wire liner worn 5. Wire disconnected internally 6. Contact tip clogged 1. Reload wire 2. Replace wire spool 3. Tighten tensioning screws if wire is slipping 4. Replace liner 5. Call 1-800-746-5641 for assistance 6. Replace contact tip (Aluminum) Wire burns back into tip or (Aluminum) Metal bubbles or burns through 1. Wire speed too slow 2. Travel speed too slow or heat is too high 1. Run speed in 7 - 10 range 2. Increase the travel speed or red

Скачали: 4   Размер: 736 kb   Производитель: Campbell Hausfeld  
Категория: Диктофоны
@name@name@name

jump back toward operator. important to support the work no pueden cortarse desde un borde. y use las velocidades mas bajas. Use the Kickback is the result of tool misuse Se pueden comenzar con un orificioPara los cortes internos sin un corte properly to minimize body exposure, power and/ or incorrect operating procedures • No doble, tuerza ni fuerce la hoja. Sipretaladrado o la sierra vertical puede tool, accessories and tool bits etc. in de entrada desde el borde, haga un blade binding, or los

Скачали: 19   Размер: 3 mb   Производитель: Campbell Hausfeld  
Категория: Диктофоны
@name@name@name

Each regulator is designed to be used with a specific gas or mixture of gases. The argon and argon mixture use the same thread type. The 100% carbon dioxide uses a different thread type. An adapter is available at your local welding gas supplier to change between the two. HOOKUP PROCEDURE ! WARNING Cylinder gas is under high pressure. Point cylinder outlet away from yourself and any bystanders before opening. 1. With cylinder securely installed, stand on side of cylinder opposite cylinder outlet

Скачали: 12   Размер: 3 mb   Производитель: Campbell Hausfeld  
Категория: Диктофоны
@name@name@name

Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. BUILT TO LAST Wire Feed Arc Welder QUALITYASSURANCEPROGRAM Need Assistance? Call Us First! 1-800-746-5641 Description This line of Campbell Hausfeld wire feed welders is designed to be used on standard 1





Категории