Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
dial can also be used to select a preset. SET TAPE SPEED 5 2 Press SP/LP. Check the SP/LP indicator on the recorder display panel to confirm the selected tape speed. c Picture quality of LP recordings will not be as high as SP recordings. 1 2 4 5 3 6 8 0 7 9 2 1 3 TV PROG. SP/LP 4,53 PLAY RECORD4 STOP6 NUMBER2 START RECORDING Press and hold RECORD and PLAY on the remote control, or press RECORD on the recorder. B.E.S.T. takes place at the beginning of both the first SP and the first LP recording after inserting the cassette (Z pg. 21). PAUSE/RESUME RECORDING 2 Press PAUSE. Press PLAY to resume recording. PAUSE 5 STOP RECORDING Press STOP on the remote control or STOP/EJECT on the recorder. Then press STOP/EJECT to remove the cassette. Accidental erasure prevention c To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape. Record safety tab 21 21 B.E.S.T. Picture System The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “ON”. Recording LOAD A CASSETTE 2 4 5 4. If not, press PUSH JOG. to place the pointer next to 1 1 Insert a cassette with the record safety tab intact. c The recorder power comes on automatically. ACCESS MODE SELECT 1 2 4 5 3 6 8 0 7 9 2 1 3 6 q PLAY RECORD RECORD PUSH JOG % 3 3 MODE The default setting is “ON”. If this is the case, go to step SCREEN Press MODE. The On- Screen/B.E.S.T. screen appears. ON SCREEN : ON B.E.S.T. : ON [5°]: SELECT [ ]: ON/OFF [MODE] : EXIT 5 CONFIRM B.E.S.T. STATUS “B.E.S.T.”, then press PUSH JOG to set to “ON”. CLOSE MODE SELECT SCREEN Press MODE. START RECORDING Press and hold RECORD and PLAY on the remote, or RECORD on the recorder. c The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording. c When the "BEST" indicator begins blinking, that means adjustment is complete. Display Panel Indication As the tape check progresses, the “– –” marks on the display panel increase upward. Once the "BEST" indicator starts blinking, the check is complete. 22 22 RECORDING (cont.) 1 2 4 5 3 6 8 0 7 9 2 1 3 6 q PLAY PAUSE PAUSE RECORD RECORDPLAY NOTES: c The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording. c In the case of timer recording, the B.E.S.T. system works before recording is initiated. c Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re- performed. ATTENTION: Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps: 1) Press and hold PAUSE and RECORD to engage the RECORD PAUSE mode. c The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, reenters RECORD PAUSE. 2) Press PLAY to start recording. c If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 3 on page 21. Playback The recorder assesses the quality of the tape once you initiate playback. When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well. 1 START PLAYBACK Press PLAY . c The recorder adjusts the playback picture quality based on the quality of the tape in use. c B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s display panel. NOTES: c When watching a rental tape, or one recorded on another video recorder, set B.E.S.T. to your preference by performing steps 2 through 4 on page 21. c "BEST" only appears at the beginning of automatic tracking. Even though it doesn't appear after that, the B.E.S.T. function is operative. 2323 % You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. On-Screen 1 2 5 TURN ON THE RECORDER Press OPERATE. Displays 6 q 1 2 4 5 3 6 8 0 7 9 2 1 3 MODE OPERATEOPERATE PUSH JOG ACCESS MODE SELECT SCREEN Press MODE. The On- ON SCREEN : ON B.E.S.T. : ON [5°]: SELECT [ ]: ON/OFF [MODE] : EXIT 5 Screen/B.E.S.T. screen appears. SELECT MODE 3 3 The pointer should already be next to “ON SCREEN”. If not, press PUSH JOG%. to place it there. ENABLE/DISABLE ON-SCREEN DISPLAY 4 4 The default setting is “ON”, so if you want on-screen displays, leave the setting as is and go to step 5. If you don’t want the displays to appear, press PUSH JOG to set “ON SCREEN” to “OFF”. CLOSE MODE SELECT SCREEN Press MODE. The superimposed indication on the TV screen tells you what the recorde...