Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
The signal adjusted by these knobs and [AUX SEND] master knob can be sent to an external device, such as an effect unit. AUX 1; Send ttie signal to the [AUX SEND 1] jack. AUX 2: Send the signal to the [AUX SEND 2] jack. 0: The signal is not sent to either output. (7) AUX send select switches [AUX SEL] These switches select the signal to be sent to AUX send. CH: The signal from the [INPUT] fader will be sent to AUX send. FB: The signal from [FB] will be senl lo AUX send. CD Parametric equalizer knobs [LOW/MID/HIGH] These knobs control the low frequency range (100Hz ±12dB), middle range (200Hz-5kHz ±12dB), and high frequency range (1 0kHz±12dB) of either ihe channel 5, 6 (Balanced or Unbalanced} signal, or the stereo bus L/R signal for fine tonal adjustment. The [EQ SEL] switch determines which signal isaffected by these knobs. ^ (9) Equalizer select switches [EQ SEL] This switch selecls Ihe signal that is controlled by the parametric equalizer. INPUT 5, INPUT 6: The signal Input to [INPUT] jacks 5 and 6 (Balanced or Unbalanced) will be controlled by the equalizer. HIGH;10kHz (High frequency range) MID :Use the SHIFT knob to set the frequency point between 200Hz and 5kHz, and use the MID EQ knob to cut/boost the selected point. (Middle frequency range) LOW:1QOHz (Low frequency range) Li R: The stereo bus L'R signal will be controlled by the equalizer. 9 a IAPTEK 2 Control panel and front and rear panels © AUX send master level knobs [AUX SEND 1 ] [AUX SEND 2] These knobs adjust the level of the mix signal after the channel [AUX] send knobs, before il is sent In the external effer.l unil via [AUX SEND t] and [AUX SEND 2]. Note:- If these knobs are set to 0, no signal is sent to the effort unit even if the channel [AUXj send knobs are raised. © AUX return 1, 2 knobs [AUX RTN 1] [AUX RTN 2] These knobs control the signal sent to the stereo bus L/Rfrom external devices (such as effect units) connectcd to the [AUX RTN 1] and [AUX RTN 2] jacks. That is, the signal processed by ihe effect unit is sent (o the stereo bus L/R. © Pitch control knob [PITCH] This knob allows you to adjust the tape speed within a range of ±10%. When the knob is in the center position ("0"), the tape speed will be high (9.5 cm/s). This control does not function when the normal speed (4.7 5 cm/s) is selected. @ Monitor select switch [MON SEL] I his switch selects the signal to monitor through the headphones or monitor speakers. STEREO: The signal that is output from the (STEREO OUT L] and [R] jacks will be monitored. ST+FB: The signals from [STEREO OUT L] and JR] jacks and from the [FB] jack will be monitored together. FB: The signal from the [FB] jack will be monitored. ® Monitor level knob [MON] This knob controls the volume of the external monitor or headphones. © Master fader [MASTER] This fader controls the signal that is output from [STEREO OUT L] and [R]. This is also used to control the output level or recording level for tracks during mixdown. ® Deck transport This is where the casscttc tape is inserted. When you install a cassette tape, the transport indicator [c] lights up. © Operation indicator [a] ,_I_, 1 2 3 4 L R TAPE LMUNT - DBBD ,•►■►►044, I RECtRACK I TRANSPORT [g] ra [a]: Bargraph level meters Track level 1-4: These meters indicate the level of each track input signal, and playback signal. Stereo bus L, R: These meters indicate the level of STEREO OUT L and R, and stereo bus output signal. [b]: Tape counter [TAPE COUNT] This displays the tape location. To reset the counter to [000], press the [COUNT RESET] key. [c]: Tape transport indicator This indicator lights up when you insert a cassette tape, indicating the transport status (direction/ speed/stop). [d]: Dolby C NR indicator This indicator lights up when you press the (DOLBY NR] switch to turn the Dolby C noise reduction system ON. 10 [ej: Rehearsal indicator This indicator lights up when you press the [REHEARSAL] button to turn rehearsal mode ON. [f]: Transport Indicator STOP = ■ PLAY = ► F FWD = ►► REWIND = -4-4 REC= • (flashing: recording stand-by, lit: recording) ORTN- ► ►0 or 0-4-4 [g]: Record track indicators These indicators display the recording status of tracks 1-4. Flashing=recording stand-by Lit=recording The indicator of the track for which the [REC SELECT] switch is ON will flash. Pressing the [PLAY] button while holding down the [REC] button will change the indicator from flashing to lit, indicating that recording mode is entered. ® Record track select switches [REC SELECT] These switches seicct the track(s) that will be recorded. If these are set to "OFF", the signal will not he recorded on any track. Select "1-4" to make direct recording of the instruments connected to [INPUT] jacks 1-4. Select "L, R" if you are recording the signal output from the stereo bus L and R. Tracks 1 and 3 will record the stereo bus L signal, and tracks 2 and 4 will record the stereo bus R signal....