Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
(Example: February 14, 2005) - 2 - - 4 - - 5 - 4 Hold Setting the HOLD switch to the HOLD position. All operation buttons are disabled. This feature is useful when the recorder has to be carried in a handbag or pocket. Remember to reset the HOLD switch when using the recorder. Notes s The recorder functions as follows with the HOLD switch set to the HOLD position: – If the recorder is playing, the display goes dark when playback of the current file has completed. – If the recorder is recording, the display goes dark when the recorder stops recording automatically upon running out of free memory. U1-BZ8099-02 AP0504 Current folder - 3 - 4 To Pause Recording To Pause Press the REC button during recording. . “PAUSE” appears on the display and the recording/playing lamp flashes. To Resume Recording Press the REC button again. . Recording will resume at the point of interruption. Notes s If “FULL” appears on the display, you cannot record. In such a case, erase unnecessary files or download to PC. s If the recorder is placed directly on a table when recording a meeting, it tends to pick up table vibrations. Put a notebook or other item between the table and the recorder for clearer recording. s Even if you press the FOLDER/MENU button, the display will not change to current recording time if the remaining recording time is 5 minutes or less. s A beep will sound when remaining recording time reaches 60 seconds, 30 seconds, and 10 seconds while recording. s When remaining recording time is less than 60 seconds, the recording/playing display lamp starts flashing in red. When the recording time is decreasing to 30 or 10 seconds, the lamp flashes faster. s The recorder will enter Stop mode if it has been left paused for 60 minutes or longer. s In case of difficult acoustic conditions or low speaker’s voice, recording in HQ or HQ is recommended. Also, usage of an external microphone (sold separately) could improve the quality of recordings. s The input level cannot be adjusted on this recorder. When you connect the recorder to an external device, execute a test recording and adjust the output level of the external device. 1 Lightly press down on the arrow and slide the battery cover open. 2 Insert size-AAA alkaline battery, observing the correct polarity. 3 Close the battery cover completely by pressing to the direction A, then sliding to the direction B. Time/Date screen appears. The hour indicator flashes, indicating the start of the Time/Date setup process. (See “Setting Time/Date (TIME)” for details) An optional Ni-MH Rechargeable battery (BR401) from Olympus can be used for the recorder. Replacing the Battery When appears on the display, replace the battery as soon as possible. Size-AAA alkaline battery is recommended. When the battery is depleted, appears on the display, and the recorder shuts off. s When replacing the battery, make sure that you turn the POWER switch OFF before replacing them. s If it takes longer than 15 minutes to replace the dead battery, you may have to reset the time when you load a fresh battery. 4 Inserting a Battery 1 Press and hold the MENU button for 1 second or longer. 2 Press the FF or REW button until “TIME” flashes on the display. 3 Press the PLAY button. The hour indicator flashes. 4 Press the FF or REW button to set the hour. 5 Press the PLAY button to select the minute. The minute indicator flashes. 6 Press the FF or REW button to set the minute. Repeat steps 5 and 6 to continue to set the year, month and date in the same way. 7 After setting the date, press the PLAY button. This completes the time/date setup procedure. 4 Setting Time/Date (TIME) If you have set the time and date, information as to when a sound file was recorded is stored automatically with that file. When using the recorder for the first time, or after the battery has been taken out for a log period of time, the hour indication will flash. In such a case, be sure to set the time and date by following steps 4 through 7 described below. 4 Notes on the Folders The recorder provides five folders, A, B, C, D and E. To change the folder selection, press the FOLDER button while the recorder is stopped. Each recorded file is stored in a folder. Using folders to classify files makes it convenient to find files you want to access later. Up to 199 messages can be recorded per folder. 4 Recording from External Microphone or Other Devices The external microphone and other devices can be connected and the sound can be recorded. s When the external microphone is connected to the microphone jack of the recorder, the built-in microphone will not operate. s When connecting an external microphone or other external equipment to the microphone jack, choose adequate equipment, such as a mono microphone (optional). - 1 - 4 How to Use the Strap 4 Power Supply Power on…Turn the POWER switch ON. If the POWER switch on the backside of this recorder is turned OFF, it is not possible to use any of the functions. Turn the POWER switch ON b...
Эта инструкция также подходит к моделям:Диктофоны - DIGITAL VOICE RECORDER WS-200S (506.73 kb)