Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Harnessanchor buckle 30 6.1.2 5-Point Harness 1. Depress the harness adjustment buttonunder the seat flap . Pull the shoulder straps out to loosen the harness. 2. Behind seat, remove the ends of the two shoulder straps from the metal junctionplate . 3. From front, pull straps through theharness slots and then reinsert them through the appropriate slots. 4. Behind seat, push both shoulder straps UNDER owner’s manual pocket and out the bottom. 5. Reassemble the strap ends onto themetal junction plate . Follow the appropriate instructions for a smalleror larger baby on the following page. Harness adjustment button 6. SAFETY CHECK: After the harness has been completely reinstalled, a) CHECK that harness straps are not twisted in front or back. b) CHECK that straps are secure by pulling on them. 31 FOR SMALLER BABY: Use the lower harness slots . (if they are even with or just below your child’s shoulders) and the upper strap loops .The ends of the straps must hang in front of the metal plate as shownin , not as shown in . CHECKthattheloopsarecompletelywithinjunctionplateslots. CHECKthatstrapsaresecurebypullingonthem. FORLARGERBABY: Use upper harness slots and the end strap loops . CHECK that the loops are completely within junction plate slots . CHECK that straps are secure by pulling. on them. 32 6.2 Securing Child in Infant Restraint Failure to properly secure your child in the infant restraint/carrierincreases the risk of serious injury or death from suffocation orfalls, or in the event of a sudden stop or crash. Even when usedonly as a carrier, make sure the harness straps are properlysecured. 1. 2. Open harness clip bysqueezing both sides andunbuckle as shown . 3. Place your child in the infant restraint as shown in , not . Pull the harness strapsdown over your child. 4. Follow directions for yourharness: 6.2.1 3-Point Harness: p. 34 6.2.2 5-Point Harness: p. 35 Moveinfantrestrainthandletosittingposition(seepage13). OR 33 6.2.1 3-Point Harness 5. Buckle harness to the latch between child’s legs. Make sure thatyou hear a “click.” DO NOT use the infant restraint if the harness does not latch in place. Call Graco at 1-800-345-4109. 6. From the back, pull strap throughharness tightener to tighten the strapsas shown . CHECK that both strapsare flat and tight on child’s shoulders. 7. Snap harness clip pieces together . Position harness clip in middle of chest,. level with armpits and away from theneck . 8. SAFETY CHECK: a) CHECK that harness straps are not twisted. b) CHECK that the harness is snug. Asnug strap should not allow any slack. Itlies in a relatively straight line withoutsagging. It does not press on the child’s flesh or push the child’s body into an unnatural position . 34 6.2.2 5-Point Harness 5. Insert the two buckle tongues into the harness buckle on thecrotch strap. Make sure that you hear each tongue click into the buckle. DO NOT use the infant restraint if the harness does not latch in place. Call Graco at 1-800-345-4109. 6. Snap harness clip pieces together . 7. Pull on harness adjustment strap to tightenstraps as shown . CHECK that both straps are flat and tight on shoulders. 8. Position harness clip in middle of chest, level with armpits and away from theneck . 9. SAFETY CHECK: a) CHECK that harness straps arenot twisted. b) CHECK that the harness is snug. A snug strap should not allow any slack. It lies in a relatively straight line without flesh or push the child’s body into an unnatural position . sagging.Itdoesnotpressonthechild’s 35 6.3 Installing the Infant Restraint/Base Using Vehicle Belt You must carefully follow the instructions provided by your vehiclemanufacturer, in addition to the information in this manual. Be sure you have read and understood section 5, “Infant Restraint Location” on p.23-28. Make sure vehicle is on level ground sothat the level indicator, which is attached to the infant restraint, can be used to properlyrecline the infant restraint . If a front passenger seat is used, slide thevehicle seat rearward as far as possiblefrom the dashboard. If a rear seat is used, make sure the seat in front of it is moved forward enough and is upright enough toallow room for the infant restraint. 1. Remove infant restraint from base, regardless of whether or notyou plan on using the base. 2. Place the base . or infant restraint without base . in a rear-facing position in a forward-facing vehicle seat. 36 3. Thread the seat belt: Base with seat belt Belt MUST go under tongue Infantrestraintwithseatbelt 4. Buckle the seat belt. Make sure the buckle tongue goes into the be twisted or turned. correctbuckle.Theseatbeltshouldnot 37 5. Tighten the vehicle seat belt. Refer to your vehicle ownersmanual and the instructions in “5.2.2 SAFE Vehicle Belt Systems”, p. 26-27, on tightening your vehicle belt. To create a very tight installation, push down hard with your kneeor free hand in the middle of the infant restraint or base . and pull and tighten the vehicle belt. 6.Pushthein...
Эта инструкция также подходит к моделям:Детские коляски - 1750713 (4.22 mb)