Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Firmly depress the gray button marked push. Insert the front wheel into axle tube on the front fork. Release button and test wheel is locked in place. If not, try again. The wheel must be firmly locked in place STEP #2 - Install Front Wheel a. PreRunner LX, 20" Wheels b. PreRunner, 16" Wheels CAUTION: DO NOT operate stroller if wheels do not firmly lock in place. Assemble footrest fender as shown in the diagram. Align the heads of the bolts to fit into the matching recesses in the footrest fender. Move quick release lever so that the word "OPEN" stamped on the lever arm shows to the outside. Insert the front wheel between the fork blades so that the axle seats firmly at the top of slots, which are at the tips of fork blades - the fork dropout. Flip quick release lever so that the word "CLOSED" stamped on the lever arm shows to the outside. Closing quick release lever should get progressively firmer until it is solidly fixed in the closed position. If quick release lever cannot be fully closed, loosen thumbnut on the opposite end of the skewer and try to close it again. If the lever goes to the closed position too easily or feels loose in the closed position, open the lever and tighten thumbnut, then try closing again. Quick release lever should be parallel to the front fork blade when in final closed position. STEP #7 - How to use the Giant PreRunner Jog Stroller braking system WARNING! Do not attempt to use the parking brake on a hill! Do not leave a child unattended in the stroller even if the parking brake is engaged! Your Giant PreRunner stroller uses a braking system similar to a bicycle. There is a brake lever at the handlebar that is connected to a brake mechanism at the front wheel. Squeeze the brake lever to make sure that it moves freely, but does not bottom out against the handlebar. Before using the stroller with a child test the brake and make sure that you can cause the front wheel to seize using the brake lever. If not, use the barrel adjusters at the brake lever and the brake mechanism on the front wheel to adjust the cable tension until the brake works to your satisfaction. The brake lever can also function as a parking brake. To engage the parking brake squeeze the brake lever and depress the button on the brake lever body until it engages. To deactivate, squeeze the brake lever until the parking brake button pops out. You're should now be ready to use. Copyright 2004 GIANT Bicycle Inc. all rights reserved 1/2004 STEP #5 -Safety Harness Instructions Caution: Make sure both shoulder straps are the same length. Open the buckle by depressing the tabs on the top and bottom simultaneously. Be sure to release both sides of the buckle. Move the harness straps out of the way and place the child in the stroller. Put the child's arms through the loops formed by the shoulder/lap straps so that harness lays over the child's shoulders. Fasten the buckle by inserting the tabs from the shoulder/lap strap into the buckle until you hear an audible click confirming that the buckle is secured. The tops of the shoulder straps should be parallel to or higher than the shoulders of the child. If they are not, remove the shoulder from the anchor strap and refasten to the anchor strap that allows you to achieve the desired position of the shoulder strap. If the child is too large for the straps to be adjusted properly do not use this stroller. STEP #6 -How to fold the Giant PreRunner Jog Stroller Push the safety button and pull the folding triggers on both sides of frame then push down. The stroller can be to fold simply. Use the fabric handle found between seat and footrest, which can be used to carry the stroller for a short distance. To unfold, lift the stroller by handlebar, and the stroller should unfold automatically. Be sure the post inside the folding hinge is locked into the frame tubing and the safety button on the folding trigger is extended. STEP #7 -How to use the Giant PreRunner Jog Stroller braking system WARNING! Do not attempt to use the parking brake on a hill! Do not leave a child unattended in the stroller even if the parking brake is engaged! Your Giant PreRunner stroller uses a braking system similar to a bicycle. There is a brake lever at the handlebar that is connected to a brake mechanism at the front wheel. Squeeze the brake lever to make sure that it moves freely, but does not bottom out against the handlebar. Before using the stroller with a child test the brake and make sure that you can cause the front wheel to seize using the brake lever. If not, use the barrel adjusters at the brake lever and the brake mechanism on the front wheel to adjust the cable tension until the brake works to your satisfaction. The brake lever can also function as a parking brake. To engage the parking brake squeeze the brake lever and depress the button on the brake lever body until it engages. To deactivate, squeeze the brake lever until the parking brake button pops out. You're should now be ready to use. ...
Эта инструкция также подходит к моделям:Детские коляски - PreRunner Jog Stroller (1.84 mb)