Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
23/1616 ” Washer Front Bushing Front Axle 2 • Turn the frame on its side. • Fit the sounds and lights box onto the dash on the topside of the vehicle. • Then, fit the retainer over the battery compartment door on the underside of the frame. Insert four #8 x 3/4” screws into the retainer and tighten. • Turn the frame upright. 3Wheel Hubcap Front Axle • Slide a wheel, smooth side first, onto the front axle. • Then, slide a hubcap, post side first, onto the front axle and into the wheel. 4Cap Nut Wheel Cover • Fit a cap nut onto the end of the front axle. • Tap the cap nut with a hammer. Gently pull the wheel to make sure the cap nut is securely attached to the front axle. • Fit a wheel cover onto the hubcap, and push to “snap” in place. 5 Assembly • First, slide a 3/1616” washer onto the front axle. • Then, insert the front axle labeled 2 up through the hole in the front end of the frame also labeled 2. 3/1616 ” Washer Front Axle Frame Front End 2 FRONT VIEW 5 Cap Nut Front Axle 6 • Fit a cap nut onto the end of the front axle, as shown. • Tap the cap nut with a hammer. • Gently pull the front wheel down to be sure the cap nut is securely attached to the front axle. • Repeat assembly steps 2-6 to assemble the front axle labeled 1, a wheel, a front bushing, a 3/16 16” washer, two cap nuts and a wheel cover. • Slide a hubcap, post side up, onto the rear axle. • Next, slide a wheel, smooth side up, onto the rear axle. • Then, slide a rear bushing, short end down, onto the rear axle. Hubcap Rear Axle Rear Bushing Wheel 9 • Slide the rear axle through the holes in the axle mounts. Rear Axle Axle MountsAx10 6 Assembly Cap Nut Covers7 Axle Mount BOTTOM VIEW 8 • Fit a cap nut cover over each cap nut on the front end of the frame. Push to “snap” in place. • Turn the frame upside down on a flat surface. • Fit an axle mount onto the pegs near the rear of the frame. Hint:Each axle mount only fits on one side of the vehicle. If it does not line up with the pegs on the frame, try fitting it to the other side. • Insert three #8 x .” screws into the axle mount and tighten. • Repeat this procedure to assemble the other axle mount to the rear of the frame. • Slide a rear bushing, long end first, onto the rear axle. • Next, slide a wheel, smooth side first, onto the rear axle. • Then, slide a hubcap, post side first, onto the rear axle. Rear Bushing Wheel Hubcap Rear Bu 11 12CapNut • Fit a cap nut onto the end of the rear axle. • Tap the cap nut with a hammer. Gently pull the wheel to make sure the cap nut is securely attached to the rear axle. Hint:You may need the help of another adult to hold the rear axle in place while you tap the cap nut. 7 Assembly 13Cap Nut Cover • Fit a cap nut cover onto each rear wheel and push to “snap” in place. 14Sounds and Lights Box Steering Wheel • Turn the frame upright. • Fit the steering wheel onto the sounds and lights box. • Insert three #6 x .” screws into the steering wheel and tighten. 17Roof Assembly • Fit the roof assembly onto the frame. Push near each post to “snap” in place. Hint:The roof assembly is designed to only fit one way. If it does not seem to fit turn it around and try again. 18CupHolder • Fit the cup holder onto the side of the frame. • Insert a #8 x .” screw into the cup holder and tighten. 8 Assembly 15Key • Fit the key into the hole in the dash. Push to “snap” in place. 16Roof Posts • Turn the roof upside down on a flat surface. • Fit the four posts into the roof and push to “snap” in place. Hint:Each post is labeled (1, 2, 3 or 4). Match the number on the post to the number on the roof. 9 10 • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles. Decoration FRONT VIEW 1 1 5 (T4444 only) 5 (M7596 Only) 5 (M7596 Only) 6 (T4444 Only) 4 2 BACK VIEW 6 (M7596 Only) 7 (M7596 Only) 7 (T4444 Only) 8 (T4444 Only) 10 (T4444 Only) 9 (T4444 Only) 3 Use Press the horn on the steering wheel for fun car songs and lights! Real working door! 11 CONSUMER ASSISTANCE 1-800-432-5437 (US & Canada) 1300 135 312 (Australia) Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052. Hearing-impaired consumers: 1-800-382-7470. Outside the United States: Canada: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2; Great Britain: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303. Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland. Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. New Zealand: 16-18 William Pickering Dri...
Эта инструкция также подходит к моделям:Детские игрушки - M7596 (957.21 kb)