Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
72 1 203017 Hex Nut, 3/8 73 2 203160 Weld Stud, 5/16-18 x 1.5 Long 74 1 920038 Inner Bracket - Black 75 1 220064 Spacer, metal, .5 O.D. x .402 I.D. x 4.96 Long 76 1 203439 Bolt, Hex, 3/8 x 6 Long 77 1 200484 Spring 78 1 220043 Concave Washer 79 1 220569 Label, Logo 80 1 960043 Cover Plate - Orange 81 2 220140 Screw, Self Tap, 1/4-20 x .5 Long 82 1 204281 Net 83 1 200119 Front Cover 84 4 265601 Bolt, Carriage, 5/16-14 x 3-1/2 Long 85 1 211249 Label, Height and Moving 86 1 202438 Rope, Nylon Double Looped Tie Down 87 1 206219 Cap *You may have extra parts with this model WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. P/N 211606A 03/02 2 printed on recycled paper HARDWARE IDENTIFIER HARDWARE IDENTIFIER (CONTINUED) Item #20 (16)* Item #11 (11) Item #10 (1) Item #39 (1) Item #5 (1) Item #15 (19)* Item #35 (2) Item #8 (6) Item #12 (1) Item #13 (1) Item #14 (2) Item #21 (1) Item #23 (1) Item #26 (4) Item #36 (1) Item #37 (3) Item #19 (1) Item #16 (1) 03/02 P/N 211606A3printed on recycled paper P/N 211606A 03/02 4 printed on recycled paper Item #43 (2) Item #53 (1) / / Item #55 (1) Item #58 (7) Item #51 (2) Item #50 (1) Item #67 (8) Item #65 (1) *You may have extra parts with this model. HARDWARE IDENTIFIER (continued) Item #46 (2) Item #54 (1) Item #59 (4) Item #60 (4) Item #69 (1) Item #71 (1) Item #72 (1) Item #75 (1) Item #73 (2) HARDWARE IDENTIFIER (continued) Item #81 (2) Item #76 (1) Item #78 (1) Item #84 (4) printed on recycled paper 03/02 P/N 211606A5 INSTRUCTIONS IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL Install trigger return spring (40) to handle assembly (32, 33) as shown. 19. Attach Accuheight label (41) to outer channel (33). 20. Attach spring (44) to pins (43) and install pins (43) onto pole mount bracket (45). Attach other spring (44) to opposite side. NOTE: Gently enlarge eyelets of spring with pliers if springs do not fit over pins. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. 21. Install pole mount assembly and reinforcement bracket (47) with carriage bolts (46) to pole as shown. Tighten flange nuts (15) completely. 22. Push back sliding pin (43) as shown in Figure A to fit adjustable system assembly through pole mount assembly. Then attach spring covers (48 & 49) onto pole mount bracket (45) with bolt (50), and nut (15) as shown in Figure B. 23. Install spacers (51) onto backboard brackets (52) with bolts (53, 54) and lock nuts (55, 37) as shown. 24. Assemble lower elevator tubes (56) as shown. NOTE : Tighten bolt (57) in lock nut (58) until flush (even) with lock nut’s outer edge. IMPORTANT! It is necessary for all parts to be installed for this mechanism to work safely and properly. NOTE: Test fit bolts into holes of brackets (52) and carefully rock them in a circular motion to ream out paint from holes if necessary 25. Starting with nuts (15) flush against board bracket (52), bolt red bracket (61) to board using bolts (60), washers (20), and foam pad (62) as shown. Do not tighten. Tightening will take place in step 30. NOTE: Place two bolts (60) through UPPER holes of red bracket only, as shown. Bend board brackets (52) to line up with holes in backboard and secure using weld studs (73), and nuts (15) as shown. 26. Assemble upper elevator tubes (63) to backboard brackets (52) as shown. NOTE: Tighten bolt (57) in locknut (58) until flush (even) with locknut’s outer edge. 27. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Then install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 28. Install upper elevator tubes (63) to triangle plates (66) as shown. Next, install handle assembly (32, 33) to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as shown. NOTE: Tighten bolt (57) in locknut (58) until flush (even) with locknut’s outer edge. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. 29. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. Insert bolt (57) through left side upper elevator tube (63), then stretch springs (68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58). 30. Install carriage bolt (69) through rim (70), washers (71) and (20) as shown. Tighten nut (72) completely. Place nut (8) about half-way up carriage bolt (69) as shown. 31. Insert inner bracket (74) into bracket (61) as shown. Insert bolts (60) through washers (20) and through UPPER holes of inner (black) bracket (74) as shown. Tighten nuts (15) completely. Tighten all hardware from step 24 at this time. 32. Insert spacer (75) through rim assembly (70). Place rim assembly on bracket (61) so that bolt (69) is inserted through hole on top of inner bracket (74). 33. Install bolt (76), through washers (20) and through top holes on side of bracket (61) and secure wi...