Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
Part No. Description 19 7 203798 Bolt, Hex 5/16-18 x 1.5" 20 4 204290 Net 21 1 206219 Pole Cap, 3" 22 3 207103 Pole Cap, 3.5" 23 2 900033 Bracket, S/J 24 1 900060 Pole, 3" 25 4 Rim 26 1 900253 Bracket, Pole Mount, No Tools 27 7 206987 Wedge 28 1 909256 Board, 48", Fan, Viper 29 1 909259 Board, 44", Fan, Evolution, NT 30 1 909602 Board, 44", Fan, Zone Attack 31 3 912006 Extension Arm 32 1 939235 Board, 48", SFA, Titanium II 33 3 990062 Pole, 3.5" 34 1 204516 Pole Sleeve HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #19 (7) Item #7 (1) Item #12 (2) Item #10 (1) Item #18 (2) Item #3 (2) HARDWARE IDENTIFIER (NUTS, WASHERS & SPRINGS) Item #17 (2) Item #9 (12) Item #11 (12) Item #16 (2) Item #15 (2) Item #14 (4) P/N 21155402 09/04 3 Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing). Corner “2” 73256 Corner “4” 80602 Corner “3” 61259 Corner “1” 9H235A Display Stand - Top View 3-1/2" 3" 3-1/2" 3-1/2" Display boards will be mounted as follows: Corner Location 1: 9H235A • 48” SFA Board • Titanium II Logo • Black Slam Jam Goal with Cover • Use extension arm for assembly Corner Location 2: 73256 • 48” Fan Recycled Board • Viper Logo • Black Slam Jam Goal • Use extension arm for assembly Corner Location 3: 61259 • 44” Fan Recycled Board • Evolution Logo • Black Standard Goal • No Tools, E3 Elevator System Corner Location 4: 80602 • 44” Fan Recycled Board • Zone Attack Logo • Black Standard Goal • Use extension arm for assembly P/N 21155402 09/04 4 At corner location 3 slide the pole sleeve (34) inside the mounting stub. 1a. 1b. Slide the 3" diameter end of the display pole (24) inside the pole sleeve. Secure the display pole by sliding the display wedge (27) into position as shown. To lock the display pole in place, tighten the hex-bolt (19). 24 24 34 27 19 At corner location 1, 2 and 4 slide the 3-1/2" diameter end of the display pole (33) inside the mounting stubs. 2a. Secure the display pole by sliding the display wedge (27) into position as shown. To lock the display pole in place, tighten the hex-bolt (19). 2b. 27 19 27 19 33 1a. 1b. Slide the 3" diameter end of the display pole (24) inside the pole sleeve. Secure the display pole by sliding the display wedge (27) into position as shown. To lock the display pole in place, tighten the hex-bolt (19). 24 24 34 27 19 At corner location 1, 2 and 4 slide the 3-1/2" diameter end of the display pole (33) inside the mounting stubs. 2a. Secure the display pole by sliding the display wedge (27) into position as shown. To lock the display pole in place, tighten the hex-bolt (19). 2b. 27 19 27 19 33 P/N 21155402 09/04 5 Corner Location 1: STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY 1. 32 7 23 Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23), extension arm (31) and mounting spacers (4) assemblies to backboard using bolt (7 ) and nut (11) as shown. Corner “2” 73256 Corner “4” 80602 Corner “3” 61259 Corner “1” 9H235A Display Stand - Top View 3-1/2" 3" 3-1/2" 3-1/2" 11 18 4 31 2. Attach board assembly to pole. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 32 9 13 22 P/N 21155402 09/04 6 7 P/N 21155402 09/04 1 17 15 16 25 23 18 • Fit rim (25) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). 3. Tighten nut (17) until flush with end of "T" bolt (18) as shown here. NOTE: 3 25 2 8 2 4. 5. Apply logo label (8) to rim cover (2). Attach cover (2) to rim using screws (3). Peel protective film from surface of acrylic backboard prior to use. NOTE: P/N 21155402 09/04 8 Corner Location 2: 48” FAN MOLDED PLASTIC BOARD ASSEMBLY 1. Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23) and extension arm (31) to backboard using bolt (7) and nut (11) as shown. Tighten completely. 28 23 11 7 18 31 18 28 9 13 2. Attach board assembly to pole. Corner “2” 73256 Corner “4” 80602 Corner “3” 61259 Corner “1” 9H235A Display Stand - Top View 3-1/2" 3" 3-1/2" 3-1/2" 22 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 3. 3. • Fit rim (25) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). 1 17 15 16 25 23 18 Tighten nut (17) until flush with end of "T" bolt (18) as shown here. NOTE: P/N 21155402 09/04 9 6 1224 Corner Location 3: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY Corner “2” 73256 Corner “4” 80602 Corner “3” 61259 Corner “1” 9H235A Display Stand - Top View 3-1/2" 3" 3-1/2" ...