Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
• Includes a non-replaceable button cell battery for toy operation. • Product features and decorations may vary from photo. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. ©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA L0538a-0726 3Pad Right Base Wire 2 Toys (Toys may be different) Adjustable Pillow Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Seat Back Tube Base Tube Left Base Wire Footrest 2 Feet NOTE: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. M5 x 20 mm Screw – 2 #8 x 1,9 cm (3/4") Screw – 2 Shown Actual Size 3Pad Right Base Wire 2 Toys (Toys may be different) Adjustable Pillow Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Seat Back Tube Base Tube Left Base Wire Footrest 2 Feet NOTE: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. M5 x 20 mm Screw – 2 #8 x 1,9 cm (3/4") Screw – 2 Shown Actual Size 4• Place the base tube on a flat surface. • Position the left and right base wires as shown. • Fit the left base wire and right base wire into the base tube. 1 IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Right Base Wire Base Tube Left Base Wire Assembly • Position the feet so the holes are toward you and the non-skid surface is down. • Fit the feet on the base tube, as shown. Feet Holes 2 • Insert an M5 x 20 mm screw through each foot and tighten. 3 • Position the footrest so that the soothing unit is upright. • Fit the footrest onto the ends of the base wires. Base Wires 4 Footrest 4• Place the base tube on a flat surface. • Position the left and right base wires as shown. • Fit the left base wire and right base wire into the base tube. 1 IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Right Base Wire Base Tube Left Base Wire Assembly • Position the feet so the holes are toward you and the non-skid surface is down. • Fit the feet on the base tube, as shown. Feet Holes 2 • Insert an M5 x 20 mm screw through each foot and tighten. 3 • Position the footrest so that the soothing unit is upright. • Fit the footrest onto the ends of the base wires. Base Wires 4 Footrest 5 Square Openings 5 Seat Back Tube • Position the seat back tube so that the square openings are upright. • Fit the seat back tube onto the ends of the base wire. • Push the seat back tube to be sure it is completely on the base wires. Assembly • Insert a #8 x 1,9 cm (3/4") screw into the inside hole of each handle and tighten. • Pull up on the seat back tube to be sure it is secured to the left and right base wires. 6 Bottom Pocket • Fit the handles through the side openings in the pad. Handles • Fit the pad seat back pocket over the seat back tube. • Pull and fit the pad seat bottom pocket around the soothing unit and footrest. Seat Back Pocket 8 7 6 Toy Bar Plugs Toy Bar Straps Sockets • Insert and “snap” the toy bar plugs into each handle socket. Hint: The toy bar is removable. Press the ends of the latches and lift the toy bar. • Fasten the toy straps to the toy bar straps. Assembly is now complete. 9 10 Assembly Hint: We recommend using an alkaline battery for longer battery life. • Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only). 1,5V “D” (LR20) +– Battery Installation • Remove the pad bottom pocket from the footrest. 1 • Insert a coin into the battery compartment door and pry the battery compartment door off. • Insert one “D” (LR20) alkaline battery into the bat- tery compartment. • Replace the battery compartment door. • Pull and fit the pad seat bottom pocket around the soothing unit and footrest. 2 Battery Compartment 6Toy Bar Plugs Toy Bar Straps Sockets • Insert and “snap” the toy bar plugs into each handle socket. Hint: The toy bar is removable. Press the ends of the latches and lift the toy bar. • Fasten the toy straps to the toy bar straps. Assembly is now complete. 9 10 Assembly Hint: We recommend using an alkaline battery for longer battery life. • Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only). 1,5V “D” (LR20) +– Battery Installation • Remove the pad bottom pocket from the footrest. 1 • Insert a coin into the batt...