Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Please re-read and repeat this assembly step. Button Rear Legs 4 Motor Housing Short Tube Tapered End Assembly 5 • Place the rear base on a flat surface so that the buttons face the front base. • While pressing the buttons on each side of the rear base, fit the rear legs onto the rear base. Push the rear legs down until the buttons on the rear base “snap” into the holes in each rear leg. Front Rear Base Base Rear Legs • Position the seat face down, with the top of the seat facing you. • Position a seat tube so that the long end is upright and toward you and the curved end is toward the outside edge of the seat. • Insert the curved end of the seat tube through the holes in the ridges on the seat back. • Repeat this procedure to assemble the other seat tube to the seat. Press Button Press Button 6 • While standing on the rear base, pull the rear legs up. They should remain secured to the rear base. If you can remove the rear legs, you have not assembled them correctly to the rear base. Reread and repeat assembly step 6. • Set the frame assembly aside for Assembly step 17. Rear Legs Pull Up Pull Up 7 Rear Base 8 Top of Seat Seat Tube Long Ends Ridges • Pull both rear legs out until they “snap” into place. Pull Rear Leg Pull Rear Leg 5 Curved End Assembly 6 • Insert four M4 screws into the seat tubes and tighten. • Rotate the seat tubes down. Seat Tubes 10 Bracket Seat Tubes 11 • Position the bracket so that the tall end is toward the bottom edge of the seat. Hint: The M4 lock nuts have been assembled to the bracket at the factory.During shipment of this product, they may have fallen out.Check to be sure there is a lock nut in each hexagonal opening on the bracket. If one (or more) has fallen out, fit the lock nut into a hexagonal opening in the bracket.Make sure the rounded side of the lock nut is facing up. • Fit the grooves on the bracket to the seat tubes, as shown. Seat Tubes Bracket Grooves Tall End Bottom Edge of Seat 9 M4 Screw - 4 Shown Actual Size Lock Nut Hexagonal Opening Shown Actual Size M4 Lock Nut Rounded Side • Fit the seat wire through the slot in the bracket as shown. Bracket Slot Seat Wire 12 Assembly 7 • While holding the seat wire in place, carefully turn the seat around so that the front faces you. • Position the seat wire cap so that the rounded edge is upright. • Fit each end of the seat wire through the hole in each seat wire cap. Ends of Seat Wire • Turn the seat face down. • Fit an accessory bin into the groove on each side of the seat, as shown. • Insert two #8 x 13/8" screws into each accessory bin and tighten. Seat Wire Cap Seat Wire Cap Grooves Seat Accessory Bin Accessory Bin 14 16 • Lift the seat tubes slightly. • With the seat wire hanging down, insert the ends of the seat wire through the slots in the seat, as shown. Slots Seat Wire 13 #8 x 13/8” Screw - 4 Shown Actual Size Seat Wire Cap Hole Rounded Edge Up 15 • Press the seat wire caps into place. • Insert two #6 x 5/8" screws through each seat wire cap and tighten. Seat Wire Caps Seat Wire is Through Hole in Seat Wire Cap Press in Place #6 x 5/8" Screw - 4 Shown Actual Size Hint: The seat wire caps are designed to fit into the seat only one way. If the screw holes in the seat wire caps do not align with the holes in the seat, try switching the seat wire caps onto the opposite ends of the seat wire. Assembly 8 • Fit the pocket on the back of the pad onto the seat back. • Fit the waist belts through the smaller slots in the pad. Crotch Belt Waist Belts Pad 19 • Lift the bottom of the pad. • Insert the pad elastic loops through the holes in the seat bottom. • Insert the crotch belt through the slot in the pad. • From under the seat, fit the elastic loops onto the tabs on the seat bottom. 20 • Insert a #8 x 13/8" screw into each frame hub and tighten. • Again, push down on the seat to be sure the seat is secured to both frame hubs. Frame Hubs 18 Pad Elastic Loops Holes Crotch Belt Seat Bottom #8 x 13/8” Screw - 2 Shown Actual Size • Position the seat assembly so that the front of the seat is toward the curved front base. • While pressing the buttons on the swing tubes, insert them into the frame hubs. Push the swing tubes up until the buttons “snap” into the hole in the frame hubs. • Push down on the seat to be sure the seat is secured in both frame hubs. Swing Tube Front of Seat Curved Front Base Push Button Frame Hub 17 9 Assembly Battery Installation Installation • Locate the battery compartment door on the swing frame. • Insert a coin into the battery compartment door and pry the battery compartment door off of the swing frame. • Insert four “D” (LR20) alkaline batteries. • Replace the battery compartment door. Battery Compartment Door Hint: When swinging, sound or power L.E.D. slows/dims/stops, it’s time to replace the batteries! We recommend using alkaline batteries for longer battery life. Battery Safety Information Batteries may leak fluids that can cause a chemical burn injury or ruin your product.To avoid battery lea...
Эта инструкция также подходит к моделям:Детские аксессуары - SMART RESPONSE B3469 (878.12 kb)