Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
•Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the toy. Dispose of batteries safely. Do not dispose of batteries in a fire. The batteries may explode or leak. •Never short-circuit the battery terminals. • Use only batteries of the same or equivalent type, as recommended. •Do not charge non-rechargeable batteries. • Remove rechargeable batteries from the toy before charging. • If removable, rechargeable batteries are used, they are only to be charged under adult supervision. 3 #8 x 1/2" Screw #8 x 1/2" Screw Assembly 1 • Insert a track into one side of the base as shown. Track Track Base 4 Base Support •Insert and “snap” the base support into the base. • Insert the other track into the opposite side of the base. 4 2 •Turn the assembly over so the bottom of the base is facing you. • Insert four #8 x 1/2" screws through the base and into the tracks. Tighten the screws. •Turn the base upright. #8 x 1/2" Screw 3 •Position the base door so that the decorated side is facing you. • Insert the peg on one end of the base door into the hole in the base. • Bend the door slightly and insert the other peg into the hole in the base. Base Door Base 6 •Turn the ramp over and insert four #8 x 1/2" screws into the back of the ramp. Tighten the screws with a screwdriver. •Repeat this procedure to attach the other ramp cover. 5 • Fit a ramp cover onto a ramp as shown. •Insert two #8 x 1/2" screws into the top of the cover and tighten them. Ramp Cover Ramp Bottom View #8 x 1/2" Screw 7 •Position the Ferris wheel assembly so that the back is facing you. •Fit one of the ramps on the back of the Ferris wheel assembly as shown. • Insert four #8 x 1/2" screws through the ramp and into the Ferris wheel assembly. Tighten the screws. •Repeat this procedure to attach the other ramp to the Ferris wheel. Ferris Wheel Assembly Ramp #8 x 1/2" Screw #8 x 2" Shoulder Screw 9 Hub • Rotate the Ferris wheel down toward the base. The arch should “click” in place. •Insert a #8 x 2" shoulder screw into the hub on the end of one ramp. Tighten the screw. •Insert the other #8 x 2" shoulder screw into the opposite hub. Tighten the screw. Ferris Wheel Assembly 7 •Position the Ferris wheel assembly so that the back is facing you. •Fit one of the ramps on the back of the Ferris wheel assembly as shown. • Insert four #8 x 1/2" screws through the ramp and into the Ferris wheel assembly. Tighten the screws. •Repeat this procedure to attach the other ramp to the Ferris wheel. Ferris Wheel Assembly Ramp #8 x 1/2" Screw #8 x 2" Shoulder Screw 9 Hub • Rotate the Ferris wheel down toward the base. The arch should “click” in place. •Insert a #8 x 2" shoulder screw into the hub on the end of one ramp. Tighten the screw. •Insert the other #8 x 2" shoulder screw into the opposite hub. Tighten the screw. Ferris Wheel Assembly Ramp Track Base Door Hub 8 Ferris Wheel •Position the base assembly so that the base door is facing you. •Position Ferris wheel assembly so that the decorated side is facing you. • Fit the hub on the end of one ramp onto the track as shown. •Bend the track slightly and fit the other hub to the opposite side of the track. 5 Kick-Activated Gym Kick-Activated Gym •To convert to a Kick-Activated Gym, pull up on the center clamp under the Ferris wheel to “snap” the arch into position. • Snap the balls onto the pegs on the Ferris wheel. • Snap the spinning toys into the clamps under the Ferris wheel. •Slide the mode switch to the I position. •Slide the volume switch on the back of the Ferris wheel to either low volume or high volume . • Baby can kick the base or bat at the toys for about five minutes of fun music, sound effects and colorful spinning balls. •Slide the mode switch to O to turn power off. Clamps Spinning Toy Pegs 6 Mode Switch Volume Switch Sit-Up Fun Sit-Up Fun •To convert to Sit-Up Fun, press the button near each ramp cover at the same time, push the Ferris wheel down until it “clicks” into position. •“Pop” the colorful balls off the pegs on the Ferris wheel. • Fit the spinning toys onto the pegs in the ramp covers or on the track. • Open the base door. •Slide the mode switch to the II position. •Slide the volume switch on the back of the Ferris wheel to either low volume or high volume . • Drop the colorful balls through the openings in the base or place balls in the Ferris wheel and watch them roll down the ramps. Short music plays as lights flash encouraging continued play. •Slide the mode switch to Oto turn the power off. 7 Mode Switch Volume Switch Button Button Base Door Pegs Consumer Information Consumer Information Questions? We’d like to hear from you! Call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Fisher-Price® Consumer Relations 636 Girard Avenue East Aurora, New York 140...