Оценок - 6, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
As well as bottles and breastfeeding accessories, you can sterilise any other boilable items (please refer to the manufacturer’s instructions regarding sterilisation). Please take a few minutes to read through the ENTIRE INSTRUCTION LEAFLET before using your iQ24 Steriliser for the first time. PLEASE SAVE THESE INSTRUCTIONS. Also available at 2 Remove all items from inside the steriliser body. 1. Measure exactly 90ml of water and pour in. 2. Assemble the blue components (baskets, stem and bottle rack) and place into the steriliser. Put the lid on. 3. Connect the lead into the back of the steriliser and plug into the mains supply. 4. The unit will display a flashing ‘0’ to indicate you need to select a mode. One short press of the control button will display a flashing ‘1’. Hold the control button in for 2 seconds then release, and a rotating ‘0’ is displayed. Mode 1 is now in progress. 5. After the water has reached 100°C, it will turn to steam. When the sterilising cycle is almost complete a numerical countdown will be displayed (see ‘Electronic Display Guide’). 6. At the end of the cycle the unit will beep 5 times. Three bars will flash and then remain displayed. 7. Let the steriliser cool down for 3 minutes. Turn off at the mains, unplug, and disconnect the lead from the back of the steriliser. 8. Remove the blue components and empty any remaining water from the unit. Wipe dry. The steriliser is now ready for use. Before using your steriliser for the first time Before each use, wash items to be sterilised in mild soapy water, and rinse. 1. Measure and pour in exactly 90ml of water if selecting Mode 1 OR 200ml of water if selecting Mode 2. 2. Slide the lower basket onto the central stem. Thread 2 screw rings onto the central stem. Slide the bottle rack down the central stem, with the neck facing down, until it rests on the top screw ring. 3. Place the teats through the centre of the holes in the bottle rack onto the lower basket. Thread 4 screw rings onto the central stem. 4. Place inverted bottles in the bottle rack and push the upper basket onto the central stem until it rests on the catch. Place dome caps and tongs into the upper basket. 5. The upper basket is not required when sterilising 330ml bottles. 6. Place the assembled unit into the steriliser body and put the lid on. Put the lead into the back of the steriliser body and plug into the mains supply. A flashing ‘0’ will appear, indicating that you need to select a mode. 7. To select Mode 1, press the control button once and the mode number will be displayed. To run this mode, hold the control button in for 2 seconds, then release. A rotating ‘0’ will be displayed. Mode 1 is now in progress. OR To select Mode 2, press the control button twice and the mode number will be displayed. To run this mode, hold the control button in for 2 seconds, then release. Three ascending and descending bars will be displayed. Mode 2 is now in progress. 8. Do not remove the lid until the 6 minute sterilising cycle has ended. This is indicated by 5 beeps and 3 bars being displayed. It is recommended to let the steriliser cool down for 3 minutes after the sterilising cycle has been completed. Items will remain sterile for up to 6 hours provided the lid is not removed. After 2 hours, the display will show 2 bars and, after a further 2 hours, one bar. To indicate the end of Mode 1 or 2, the unit will sound a long beep followed by a flashing ‘0’ †. At this point items should be used immediately or resterilised. (Please refer to ‘To remove sterilised items after a cycle’ on page 5). Switch off at mains and unplug the lead from the back of the steriliser. Pour away any remaining water, rinse out the inside of the steriliser body and wipe dry. † The end of a cycle is 6 hours after commencement of Mode 1 and 24 hours after commencement of Mode 2. The unit can be completely stopped at any time during a cycle, by pressing and holding in the control button for 2 seconds. The unit will beep and a flashing ‘0’ will be displayed, indicating the unit has returned to selection mode. * to sterilise the ISIS Breast Pump or other items please refer to page 5 Sterilising in Mode 1 – 6 hour sterile period Sterilising in Mode 2 – 24 hour sterile period To sterilise up to six 125ml, 260ml or 330ml AVENT Bottles* 4 Dishwasher Basket 1. Two baskets can be clipped together to hold small items such as teats, breast pump parts etc. for washing in the top rack of your dishwasher prior to sterilisation. 2. To clip together, align the baskets so that the indicators are opposite each other and snap the baskets together. To open, pull apart with fingers. 1. When Mode 1 cycle is complete pressing the button will reset the unit. 2. In Mode 2 (after sterilised) when 3x bars are displayed, pressing the button will pause the cycle, allowing removal/addition of item. Pressing the button again will resume the cycle (re-sterilise). The unit will immediately enter a new sterilisation pha...
Эта инструкция также подходит к моделям:Эхолоты - IQ24 (454.09 kb)