Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
From essential safety aids to developmental playthings, our products uphold our permanent commitment to safety, while offering the extra convenience, durability, and innovation you need to care for your growing child. WARNING: • This bouncer is designed for children who weigh LESS than 25 lbs. (11.3 kg). • READ all instructions before use of the Bouncer. • KEEP instructions for future use. • DO NOT use this Bouncer if it is damaged or broken. • ALWAYS use the restraint system. • NEVER leave child unattended. • NEVER use for a child who is able to push up on hands and knees, pull up, or sit up unassisted. • FALL HAZARD: • Child’s movement can slide Bouncer. • NEVER place product on countertops, tables, or other elevated surfaces. • NEVER lift Bouncer with child in it. • NEVER use Bouncer as car seat. Interactive Discovery Bouncer 25033/25120 User Guide Questions? Comments? Missing Parts? Contact Us: (800) 544-1108 Keep These Instructions For Future Use • Adult assembly required. CAUTION: • Keep small parts away from child during assembly. • Read all instructions before assembly and use of bouncer. • Lay out and identify all parts. • Remove all contents from packaging and discard box, and/or poly bags. • Do not return this product to the place of purchase. If any parts are missing, call Consumer Relations at (800) 544-1108. Or visit our web site at • Include the model number (25033) and date code (manufacture date) located on back of fabric seat. • Batteries not included. 1 “C” sized and 3 “AAA” sized alkaline batteries needed. Dispose of batteries safely. ©2003 Dorel Juvenile Group Made in CHINA (800) 544-1108 Styles and colors may vary. Distributed by Dorel Juvenile Group, Inc., 2525 State Street, Columbus, IN 47201-7494 In Canada: 12345 Albert-Hudon, Suite 100, Montreal-N, QC Canada H1G 3K9 up to 11.3kg 25lbs Parts List A B E H G F Curved Footrest Fabric Seat (with restraint system) Caterpillar Toy Flower Toy Curved Headrest Vibration Unit A B C Screws (see hardware box) Rear Leg Connector Left Leg G H I D E F C NOTE: Date Code is located on back of fabric seat. I Tools Needed: Phillips Head Screwdriver Hardware (Quantity): M3 x 23mm Phillips Head Headrest Screw, (1) M3 x 23mm Phillips Head Vibration Unit Screw, (1) Right LegJ J D To Install Batteries 1 Locate the vibration unit. Use a Phillips Head A screwdriver to remove the screw on the battery door. Place a C-sized battery inside. Match the (+) and (-) symbols according to the diagram in battery compartment. B Locate the Caterpillar toy. Use a Phillips Head screwdriver to remove the battery door. Place three 1 A B AAA-sized batteries inside. Match the the (+) and (-) symbols according to the diagram in battery compartment. NOTE: Batteries not included. NOTE: Vibration Unit and Caterpillar will not operate if batteries are installed incorrectly. To Assemble BATTERY CAUTION: • Keep these instructions as they contain important information. • DO NOT mix old and new batteries. • DO NOT mix alkaline, standard (carbon zinc), or rechargeable (nickel-cadium) batteries. • Non rechargeable batteries are not to be recharged. • Rechargeable batteries are to be removed from the unit before being charged. • Rechargeable batteries are only to be charged under adult supervision. • Only batteries of the same or equivalent type as recommended are to be used. • Batteries are to be inserted with the correct polarity. • Exhausted batteries are to be removed from the unit. • The supply terminals are not to be short-circuited. • Check that all contact surfaces are clean and bright before installing batteries. • DO NOT submerge any part of the product in water. • Dispose of batteries safely. • Remove batteries when stored for long periods of non-use. 1 Legs: Line up flat edge of Right Leg with dimple on Rear Leg Connector (Figure 1). Insert leg and rotate counter clockwise. Line up flat edge of Left Leg with dimple on Rear Leg Connector (Figure 1a). Insert leg and rotate clockwise. Tug on leg joints to check security of connections. NOTE: The Legs are designed to fit firmly into the Headrest Frame to ensure they stay in place. As a result, you may experience some resistance when installing the Headrest Frame. 1 Rear Leg Dimple 1a Flat Edge Flat Edge Rear Leg Dimple Right Leg Left Leg PAGE 2 To Assemble (continued) 2 Footrest Frame: Position so curved loops points downward (Figure 2). Slide Footrest Frame on right side and then left side (Figure 2a). 2 Curved Loops Footrest Frame 2a 3 Vibration Unit: Locate the Vibration Unit and Vibration Unit Mounting Screw. Slide Vibration Unit onto Headrest Frame and align with screw hole. Insert Mounting Screw through Vibration Unit and into Headrest Frame (approximately 1/4 of the screw should be showing). Secure together using a Phillips head screwdriver (Figure 3). NOTE: When tightening screw, make sure it engages to Headrest Frame. If needed, slightly reposition Vibration Unit unti...