Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
2 Consumer Information Great Britain: Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303. Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland. Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Tel: +603-3341 9052. • Please read these instructions before assembly and use of this product. • Adult assembly is required. Tool needed for assembly: Phillips screwdriver (not included). • Requires one "D" (LR20) alkaline battery (not included) for soother operation. • Product features and decorations may vary from photographs. Parts Seat Back Tube 2 Side Rails Cross Brace 4 Retainers with Lock Nut Front Tube Pad IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Kickstand Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. M5 x 30 mm Screw – 8 Shown Actual Size WARNING To prevent serious injury or death: • Fall Hazard - It is dangerous to use this reclined cradle on an elevated surface, since child's movement may cause the product to slide or tip over. Use only on a fl oor. • Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion) since product can tip over and cause suffocation in soft surfaces. • Always use the restraint until child is able to climb in and out of the product unassisted. • Never leave child unattended. • Use the upright position only when child has developed enough upper body control to sit without leaning forward. • Never use as a carrier or lift while child is seated. Never use the toy bar as a handle. • Reclined position not recommended for children who can sit up by themselves (6 months approximately, until 9 kg). CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA H5985d-0726 3 Toys Toy Bar 3 Assembly • Position each side rail so that the button faces outward. • Insert the seat back tube into the socket in each side rail. • While pressing the tabs on the ends of the seat back tube, continue to insert the seat back tube into the sockets in each side rail, until the tabs “snap” into place. Make sure you hear a “snap” on each side. • Pull the seat back tube up to be sure it is secure in the side rail sockets. IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Seat Back Tube Side Rail Sockets PRESS TABS Button 1 • Fit the cross brace between the side rails, as shown. Cross Brace 2 Side Rails • Insert a screw through each side rail and into the ends of the cross brace. 3 • Fit a retainer with lock nut onto the end of the screw and to the inside of a side rail. Tighten the screw. Hint: A lock nut has been factory assembled to the retainer. During shipment, the lock nut may have fallen out of the retainer. If it has, please fit it into the hexagonal hole in the retainer so that the rounded side of the lock nut faces out. • Repeat this procedure to fasten the screw in the other end of the cross brace and side rail, using the remaining retainer with lock nut. 4 4 • Locate the hole in each side rail. • With the vibrations unit facing forward, fit the front tube to the side rails, as shown. Hold the front tube in place and proceed to step 6. • Insert a M5 x 30 mm screw through the outside of each side rail and into the ends of the front tube. IMPORTANT! Please follow the next assembly (step 7) carefully to completely secure the front tube to the side rails. Side Rail Hole Side Rail Hole Vibrations Unit Front Tube 5 6 Assembly Retainer with Lock Nut • Fit a retainer with lock nut onto the end of the screw and to the inside of a side rail. Tighten the screw. Hint: A lock nut has been factory assembled to the retainer. During shipment, the lock nut may have fallen out of the retainer. If it has, please fit it into the hexagonal hole in the retainer so that the rounded side of the lock nut faces out. • Repeat this procedure to fasten the screw in the other end of the front tube and side rail, using the remaining retainer with lock nut. • Fit the kickstand onto the assembly, as shown. • Insert two screws into the holes on each side rail and tighten. 7 Kickstand 8 5 • Fit the upper pocket on the pad onto the seat back tube...