Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Attach the rails to the INSIDE FACE of the END PANEL. The inside face has countersunk areas for the rails and slots that you will use later for the mesh basket. Position the bottom rails with the grooves facing up; and position the top rails with the grooves facing down. Slip the TWO NYLON SNAP STRAPS (D) over the TOP RAILS (B). Position them so that they are ready to snap to the snaps on the bassinet body (H). STEP 2: See PICTURE 2. Attach the second END PANEL (A) to the FOUR RAILS (B) using FOUR BOLTS (C). STEP 3: See PICTURES 3A and 3B. Turn the bassinet stand upside down. Insert the TWO DOWELS (E) through the edge pockets of the MESH BASKET (F). Insert the ends of the ONE DOWEL (E) into the SLOTS cut into the inside faces of the END PANELS (A). Stretch the mesh basket over the rails and around to the other side, and insert the second wood dowel into the dowel slots. Adjust the mesh basket to remove wrinkles. Attach the FOUR CASTER WHEELS (G) to the corners of the end panels using one BOLT and one KNOB for each WHEEL. The knobs go on the inside. PICTURE 3A Page 4 of 6 B AB B B D PICTURE 2 A STEP 4: See PICTURES 4A and 4B. Turn the bassinet stand over. Fit the slots on the BASSINET BODY (H) over the raised edge pieces on the top of the END PANELS (A). See PICTURE 4A. Next, snap the NYLON SNAP STRAPS (D) onto the snaps on the bottom edge of the BASSINET BODY (H). See PICTURE 4B. 3.0/1108/TG STEP 5: Unpack the BEDDING SET (I). You may launder the set before use if you wish, and/or iron, press, or steam it to remove wrinkles. Machine wash cold, gentle cycle only; air dry or tumble dry low or no heat. Iron on lowest setting for poly/ cotton. Locate the buttonholes on the FABRIC LINER and slip them over the spools on the BASSINET BODY (H). Smooth the liner around the sides and bottom inside the bassinet, and adjust it around the outside of the bassinet. Put the SHEET onto the MATTRESS PAD (J) and place the mattress pad into the bassinet. Snap together the HOOD HOOP FRAME (K) as shown in PICTURE 5. Stretch the fabric HOOD over the FRAME and slip the elastic loops over the ends of the frame to hold the hood in place. Snap the FRAME (K) onto the spools on the BASSINET BODY (H). The bassinet is now ready for your baby! See PICTURE 6. PICTURE 3B “Puzzle Piece” Fit PICTURE 4A Snap Straps PICTURE 6 NOTE: Your bassinet bedding may vary from shown PICTURE 4B Raised Liptowards front PICTURE 5 Page 5 of 6 3.0/1108/TG PICTURE 7 To use the bassinet as a Rocking Cradle, loosen the caster knobs, rotate the casters into the up position, and retighten the knobs. See PICTURE 7. TO CONVERT THE STAND TO A TOY BOX PICTURE 8 STEP A: Remove the bedding, bassinet body, hood, wooden dowels, and mesh basket, and set them aside. STEP B: Unscrew and remove all four of the bolts holding the TOP RAILS and set aside the screws, rails, and nylon snap straps. STEP C: Insert the two larger SIDE PANELS (L) into the grooves on the bottom rails with the white sides facing out. STEP D: ...
Эта инструкция также подходит к моделям:Детская мебель - 00750 (435.63 kb)
Детская мебель - 00752 (435.63 kb)
Детская мебель - 0850T (435.63 kb)
Детская мебель - 0852T (435.63 kb)