Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
You may set the clock from 0:00 if the set is disconnected from the wall outlet. 1 Press and hold MODE until clock digit for hour flashes. 2 Hold down . / § to adjust the hours. 3 Press MODE to confirm the hour setting. . The clock digits for minute flash. 4 Hold down . / § to adjust the minutes. 5 Press MODE to confirm the setting. Standby power consumption (clock mode) ........................ 2.4W Radio Tuning to radio station 1 Press STANDBY-ON to switch on from clock mode. 2 Press repeatedly SOURCE to select FM or MW. . The radio station frequency, waveband will be displayed briefly, then clock is displayed. is also displayed. (See 2 ) 3 Press and hold . or § until the frequency in the display star ts running. . The radio automatically tunes to a station of sufficient reception. 4 Repeat step 2 if necessar y until you find the desired station. • To tune to a weak station, press . or § briefly and repeatedly until you have found optimal reception. Programming radio stations You can store 20 FM and 10 MW radio stations in the memor y manually or automatically. Autostore Autostore automatically star ts programming radio stations from preset 1. Any previous presets e.g. manually programmed will be erased. 1 Press repeatedly SOURCE to select FM or MW. 2 Press and hold PROG until the frequency in the display star ts running. . Available stations are programmed (MW or FM). To listen to a preset or autostore station Press the PRESET +/– once or more until the desired preset station is displayed. Manual programming 1 Tune to your desired station (see Tuning to radio stations). 2 Press PROG to activate programming. . Display: P01 flashes. 3 Press PRESET +/-once or more to allocate a number (FM: from 1 to 20; MW: from 1 to 10). 4 Press PROG to confirm. 5 Repeat steps 1-4 to store other stations. Helpful hints: – You can erase a preset station by storing another frequency in its place. To improve reception: FM: Extend and adjust the pigtail for optimum reception. MW: Uses a built-in antenna. Direct the antenna by adjusting the position of your unit. This set complies with the radio interference requirements of the European Community. CD Player CD playback This CD clock radio suppor ts audio discs including CD-R (CD-recordable), CD-RW (CD-rewritable). Do not tr y to play a MP3-CD, CD-ROM, CDI,VCD, DVD or computer CD. 1 Press STANDBY-ON to switch on from clock mode. 2 If CD is not selected, press SOURCE once or more to select it. . is displayed. 3 Lift the CD door to open. 4 Inser t a CD with printed side facing up, and close the CD door. . Flashing ---- is displayed briefly, then total CD track number and the clock are displayed. (See 3) 5 Press ); to star t playback. . During the playback, the current track number is displayed instead of the total track number. 6 To view Clock, press DISPLAY. . The clock time is displayed for several seconds, then it will switch back to playback time information. 7 To adjust the sound, press VOLUME. 8 To interrupt, press ); . To resume playback, press ); again. 9 To stop playback, press 9 . 10 To switch off CD playback and back to standby, press STANDBY-ON. . The clock is displayed. Selecting a different track • Press . / § once or repeatedly until the desired track number appears on the display. • In the stop position, press ); to star t playback. Finding a passage within a track 1 During playback, press and hold down . or § . . The CD is played at high speed and low volume. 2 Release . or § when you recognize the passage you want. . Normal CD playback resumes. Programming tracks You may store up to 20 tracks in the desired sequence for playback. If you like, store any track more than once. 1 In the stop position, press PROG to enter programming mode. . P01 is displayed (See 4). 2 Press . or § to select desired track. 3 Press PROG to store the track. . P02 is displayed 4 Repeat steps 2 to 3 to select and store all desired tracks. . If you attempt to store more than 20 tracks, no tracks can be stored. 5 Press ); to play the program. . PROG is displayed (See 5) To erase a program, select any of the following. – In stop position press PROG to enter program mode and press 9 ; – Open the CD door. – Press STANDBY-ON to standby; – Select other sources. CD Player Auxiliary connection/Alarm Selecting different play modes: REPEAT and SHUFFLE You can select and change the various play modes before or during playback, and combine REPEAT modes with program. SHUFFLE – plays all tracks in random order. REPEAT – plays the current track continuously. REPEAT ALL – plays the entire disc/ program continuously. 1 To select play modes, press MODE once or more. . The selected play mode will be displayed. 2 Press ); to star t playback if in the stop postion. . When SHUFFLE mode is selected, the disc will play automatically around few seconds later. 3 To return to normal playback, press MODE repeatedly until the various modes are no longer displayed. – You can also press 9 once to cancel your play modes....