Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Character button (CHARACTER) Finalize button (FINALIZE) Number buttons (1 to 10) Use these buttons for direct search and programmed playback. Normal speed dubbing mode button (DUBBING NORMAL) High speed dubbing mode button (DUBBING HIGH) Relay mode button (RELAY MODE) Function selector switch + 10 button Use this button to enter track numbers of 11 or over for direct search and programmed playback. Call button (CALL) Use this button to check the programmed tracks. Program/direct button (PROG/DIRECT) Press this button to switch between the program setting mode and the direct search mode. Normally this is set to the direct search mode. Clear button (CLEAR) Menu button (MENU) Enter button (ENTER) . . . . Switches the operation of the buttons between the CD and CD-R. . . Title button (TITLE) Press this button to switch the time display to the title display. Input select button (INPUT) Time button (TIME) Fader button (FADER) Press this for fade-in and fade-out recording. Inserting the batteries q Remove the remote control unit’s back lid. w Insert the two R6P (AA) batteries in the battery compartment, in the direction indicated by the marks inside the compartment. e Put the back lid back on. Using the remote control unit DUBBINGNORMAL HIGH RELAY MODE ENTER8 9 MENU 6 7 32 30° 30° 2 4 3 7 8 56 1 9 10 +10 8 9 3 2 6 7 B REMOTECONTROLUNITRC-278 Approx. 8 meters the main unit as shown in the diagram. • The remote control unit can be operated from a direct distance of approximately 8 meters from the main unit. This distance will be shortened, however, if there are obstacles or when operated from an angle. (The remote control unit will operate from a horizontal angle of up to about 30° .) NOTES: • The remote control unit may not operate if the remote sensor is exposed to direct sunlight or strong artificial light, or if there is an obstacle between it and the remote sensor. Cautions on batteries • Use R6P (AA) batteries in the remote control • The batteries should be replaced with new approximately one year, though this depends frequency with which the remote control unit is used. • Even if the batteries are less than a year old, replace them with new ones if the remote control unit no longer operates even from a short distance from the main unit. • The included battery is only for verifying operation. Replace it with a new battery as soon as possible. • When inserting new batteries, wait about two minutes after removing the old batteries before inserting the new ones. • Be sure to set the batteries in the proper “< ” and “ > ” directions, as indicated by the marks in the remote control unit’s battery compartment. • Remove the batteries when not using the remote control unit for long periods of time. • To avoid explosions and fluid leakage: • Do not use one new battery with one old one. • Do not use two different types of batteries. • Do not short-circuit, disassemble, heat or dispose of batteries in flames. • If the battery fluid should leak, wipe all the fluid off the battery compartment, then insert new batteries. • When operating the remote control unit, point it at • Do not press buttons on the main unit and on the remote control unit at the same time. Doing so will result in malfunction. ENGLISH 2 Inserting Disc q Press the OPEN/CLOSE button ( 5) to open the disc tray. w Insert a disc in the appropriate up. e Press the OPEN/CLOSE button ( 5) to close the tray. • “ Close” lights up, followed by “ TOC Reading” and the display will show the type of disc • If you insert a blank or partly-recorded CD-unfinalized CD-RW, the CD recorder will calibrate disc for optimum recording. During this process display will first show “ Now OPC” and then the number of audio tracks. Calibration can take up to 60 seconds. (CD-R/RW) • If a CD-R/RW is finalized it will show “ CD” on the display. Disc tray Recess OPEN/CLOSE button ( 5) NOTES: • If your finger should get caught in the disc tray when it closes, press the OPEN/5). • For recording it is important that the blank disc is completely free from dust particles “ Disc cleaning” on Page 6. • When text information is entered but not finalized, the disc holder will not open until all deleted. “ Text Erase OK? ” will be displayed for 2 seconds. When the enter button is pressed during this interval, the text information will be deleted and the disc holder can be opened. 8 SETUP METHOD The 10 items listed below can be set with the setup menu. The following messages will be displayed for the various setting items. • Close the disc trays and set the stop mode for both the CD and CD-R sections. • The contents of the set menu are stored, but this data might be lost if the unit is disconnected from the power source for 2 to 3 days. q “ Sync. Rec? ”…………………………………………… Synchro recording mode. w “ Sync. Level? ” ……………………………………… Synchro recording level. e “ A.T. Mark? ”…………………………………………… Auto track mark. r “ FadeIn Time? ” ……………………………………… Fade-in recording time. t “ FadeOutTime? ” …………………………………… Fad...